Auto Parts Search
We have info for following modifications of 1991 Honda CRX
- 1991 Honda CRX SI 1.6 L4 GAS, CC:1590, Fuel Injection
- 1991 Honda CRX HF 1.5 L4 GAS, CC:1493, Fuel Injection
- 1991 Honda CRX 1.5 L4 GAS, CC:1493, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 1991 Honda CRX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Honda CRX cars and light trucks from 1990+.
HONDA, DISC BRAKES -> FRONT BRAKE PAD & LINING REPLACEMENT -> INSTALLATION -> REMOVAL
Vehicle: 1991 Honda CRX SI 1.6 L4 GAS
REMOVAL
- Refer to table when replacing brake pads.
- Raise and support front of vehicle, then remove wheel and tire assemblies.
- Remove brake hose clamp bolts from steering knuckle, Fig. .
- Remove caliper bolt, then swing caliper up out of the way.
- Remove shims, retainers and brake pads.
INSTALLATION
- Using a vernier caliper, measure thickness of each pad lining. Compare measurement with specifications. If brake lining thickness is less than specified, replace both pads as a set.
- Clean caliper thoroughly, and check for grooves or cr...
CLICK HERE TO GET FULL ACCESS TO 1991 Honda CRX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Honda CRX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Honda CRX cars and light trucks from 1990+.
HONDA, DISC BRAKES -> REAR CALIPER REPLACEMENT -> INSTALLATION -> REMOVAL
Vehicle: 1991 Honda CRX HF 1.5 L4 GAS
REMOVAL
Ensure dirt or other foreign matter is not allowed to contaminate brake fluid. Do not mix different types of brake fluid as they might not be compatible.
- Refer to Figs. through when replacing rear calipers.
- Raise and support rear of vehicle, then remove wheel and tire assemblies.
- Remove caliper shield, then disconnect parking brake cable from caliper lever by removing lock pin.
- Remove banjo bolt and disconnect brake...
CLICK HERE TO GET FULL ACCESS TO 1991 Honda CRX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Honda CRX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Honda CRX cars and light trucks from 1990+.
HONDA, DRUM BRAKES -> PARKING BRAKE ADJUSTMENT
Vehicle: 1991 Honda CRX HF 1.5 L4 GAS
Rear brakes must be properly adjusted before adjusting parking brake.
- Raise rear wheels off of the ground, then pull parking brake lever up one notch.
- Tighten equalizer adjusting nut until rear wh...
CLICK HERE TO GET FULL ACCESS TO 1991 Honda CRX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Honda CRX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Honda CRX cars and light trucks from 1990+.
HONDA, HYDRAULIC BRAKES -> BLEEDING BRAKES
Vehicle: 1991 Honda CRX 1.5 L4 GAS
Do not mix different brands of brake fluid as they may not be compatible. Use only DOT 3 or 4 brake fluid.
- Have an assistant slowly pump brake pedal several times, then hold steady pressure.
- Loosen brake bleed screw to allow air to escape from system, then tighten ...
CLICK HERE TO GET FULL ACCESS TO 1991 Honda CRX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Honda CRX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Honda CRX cars and light trucks from 1990+.
HONDA, POWER BRAKES -> IN-VEHICLE TESTING -> CHECK VALVE TEST -> FUNCTION TEST -> LEAK TEST
Vehicle: 1991 Honda CRX 1.5 L4 GAS
FUNCTION TEST
- With engine turned off, depress brake pedal several times, then depress brake pedal hard and hold for 15 seconds. If brake pedal sinks, a brake line, wheel cylinder or master cylinder is faulty. Repair or replace as necessary.
- Start engine with brake pedal depressed. Pedal should sink slightly. If it does not, the booster or check valve is faulty. Repair or replace as necessary.
LEAK TEST
- Depress brake pedal with engine running, then stop engine and hold brake pedal for 30 seconds. Pedal height should not...
CLICK HERE TO GET FULL ACCESS TO 1991 Honda CRX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Honda CRX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Honda CRX cars and light trucks from 1990+.
HONDA, POWER BRAKES -> POWER BOOSTER OVERHAUL -> 1989 ACCORD, 1989-91 CIVIC, CIVIC CRX & CIVIC WAGON -> 1990-91 PRELUDE -> Assembly -> Disassembly
Vehicle: 1991 Honda CRX HF 1.5 L4 GAS
On 1990-92 Accord and 1992 Civic and Prelude models, the brake booster cannot be overhauled and must be replaced as an assembly.
1989 ACCORD, 1989-91 CIVIC, CIVIC CRX & CIVIC WAGON
Disassembly
- Refer to Fig . when overhauling these brake boosters.
- Remove brake booster from vehicle as described under "Power Booster, Replace."
- Scribe aligning mark across front and rear booster housings to ensure proper positioning of parts on reassembly.
- Remove E-clips and separate booster housings, Fig. .
- Remove seals and washers from spring retainer, then the 10 millimeter snap rings, spring retain...
CLICK HERE TO GET FULL ACCESS TO 1991 Honda CRX BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1991 Honda CRX vehicle. |
Access the Complete guide! |