Auto Parts Search
Honda CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Honda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Model
| 600 | Accord | Civic | Civic DEL SOL |
| CR-V | CRX | Element | EV Plus |
| FIT | Insight | Odyssey | Passport |
| Pilot | Prelude | Ridgeline | S2000 |
| Wagovan |
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Honda car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system
specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your Honda
automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR Honda AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported Honda cars and light trucks from 1990+
Honda -> Component Replacement & Adjustment -> Condenser, Replace -> 1998 -> 1999-2000 -> Accord -> Civic -> CR-V -> Odyssey -> Prelude
Vehicle: 2000 Honda Prelude 2.2 L4 GAS
Refer to "Rodeo" for "Honda Passport" information.
Accord
- Recover refrigerant as outlined under .
- Remove coolant reservoir. Do not disconnect hose.
- Remove mounting bolts and radiator upper mount brackets.
- Remove mounting bolts, then disconnect discharge and condenser lines. Plug lines.
- Remove mounting bolts, upper mounting brackets and condenser. Do not damage radiator and condenser fins during removal.
- Reverse procedure to install, noting the following:
- Install new O-rings lubricated with suitable refrigerant oil. ...
CLICK HERE TO GET FULL ACCESS TO Honda A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR Honda AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Honda cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Power Booster Overhaul -> Power Booster, Replace
Vehicle: 1993 Honda Civic SI 1.6 L4 GAS
Power Booster, Replace
- Remove master cylinder as outlined under "Hydraulic Brake Systems."
- Disconnect vacuum hose from booster, then remove vacuum hose bracket.
- On Accord models, remove throttle control cable bracket.
- On Prelude models, remove throttle/cruise control cable bracket, then remove throttle cable grommet from engine compartment bulkhead.
- On Prelude models, remove IAT sensor from intake manifold.
- On Accord and Odyssey models, remove wiring harness from clamp.
- On Accord models with M/T, remove clutch reservoir and reservoir brac...
CLICK HERE TO GET FULL ACCESS TO Honda BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR Honda AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Honda cars and light trucks sold in the U.S. for 1980+.
Honda -> Component Locations -> 1985-00 Civic, 1993-97 del Sol & 1985-91 CRX w/Fuel Injected Engine
Vehicle: 1991 Honda Civic CX 1.5 L4 GAS
CLICK HERE TO GET FULL ACCESS TO Honda FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Honda AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Honda cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2000 Honda Passport EX 3.2 V6 GAS
Replacement procedures for left and right driveshafts are the same.
- Raise and support front of vehicle, then remove front wheels.
- Drain transaxle.
- Raise locking tab on spindle nut, then remove nut.
- Remove self-locking nut and self-locking bolt. Replace self-locking bolt if you can easily thread a non-self-locking nut past their nylon locking inserts.
- Remove damper fork, then cotter pin from lower arm ball joint castle nut and remove nut.
- Install hex nut on ball joint. Ensure nut is flush with ball joint pin end, or threaded section of ball joint pin might be damaged by ball joi...
CLICK HERE TO GET FULL ACCESS TO Honda DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Honda AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Honda cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification
Vehicle: 2008 Honda S2000 CR 2.2 L4 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
...
CLICK HERE TO GET FULL ACCESS TO Honda TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Honda AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Honda cars and light trucks from 1990+.
Starter, Replace
Vehicle: 1997 Honda Prelude SH 2.2 L4 GAS
- Disconnect battery ground cable.
- Remove engine wire harness from harness clip on starter motor.
- Disconnect starter cable from B+ terminal on solenoid, then BLK/WHT wire from S-terminal.
- On mod...
CLICK HERE TO GET FULL ACCESS TO Honda STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR Honda AUTOMOBILES
Cabin air filter locations and replacement procedures with corresponding images for most domestic and imported Honda cars and light trucks sold in the U.S. as equipped to the current model year.
Cabin Air Filter Service -> Honda -> 2005-09 Odyssey
Vehicle: 2006 Honda Odyssey EX 3.5 V6 GAS
The cabin air filter should be replaced every 30,000 miles or 24 months. If the vehicle is operated primarily in urban areas with high concentrations of soot and diesel powered vehicles, replace the filter every 15,000 miles. The filter should be replaced more often if air flow is less than normal.
- While holding the lower glove compartment, release the damper, Fig. , then remove the glove compartment stop on each side.
- Remo...
CLICK HERE TO GET FULL ACCESS TO Honda CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Honda AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Honda cars and light trucks sold in the U.S. from 1990+.
Honda -> Automatic Transmission (A/T) Fluid Temperature Indicator ->
Vehicle: 2007 Honda Odyssey EX 3.5 V6 GAS
The A/T fluid temperature lamp will turn on when ignition switch is placed in On position and should turn off after a few seconds. If lamp illuminates while driving, the vehicle should be pulled off the r...
CLICK HERE TO GET FULL ACCESS TO Honda MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Honda AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Honda cars and light trucks from 1990+
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 2006 Honda CR-V EX 2.4 L4 GAS
Inlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp with suitable tool.
- Remove hose from heater core tube.
- Reposition hose clamp with suitable tool.
- Remove hose from thermostat housing tube.
- Reverse procedure to install.
Outlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp wi...
CLICK HERE TO GET FULL ACCESS TO Honda RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Honda AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Honda cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2003 Honda Odyssey LX 3.5 V6 GAS
- Rotate or lift belt tensioner arm, using a suitable wrench to relieve tension from drive belt. This is a hydraulic type a...
CLICK HERE TO GET FULL ACCESS TO Honda SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Honda AUTOMOBILES
Component location diagrams for most Honda cars and light trucks sold in the U.S. from 1990+.
 Dashboard Wire Harness B Diagram for 2008 Honda Element EX 2.4 L4 GASComponents on diagram: |
 Engine Compartment Diagram for 2003 Honda Civic GX 1.7 L4 CNGComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Honda PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Honda AUTOMOBILES
OEM drawn wiring diagrams for most Honda cars and light trucks sold in the U.S.
 1999 Honda Civic SI 1.6 L4 GAS Wiring DiagramComponents on diagram: |
 1996 Honda Prelude S 2.2 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Honda WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Honda AUTOMOBILES
OEM TSB listings for most Honda cars and light trucks sold in the U.S. from 1985+.
|
Document: IMMOBILIZER SYSTEM (TYPE 4) - REVISED Vehicle: 2008 Honda Pilot EX-L 3.5 V6 GAS Auto Systems: |
|
Document: VEHICLE PULLING OR DRIFTING - REVISED Vehicle: 2008 Honda Pilot Special Edition 3.5 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO Honda TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Honda AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Honda cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Honda cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Honda cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Honda cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Honda SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
