Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Pontiac Bonneville car and truck
repair procedures including Pontiac engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Pontiac Bonneville automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2000 Pontiac Bonneville
- 2000 Pontiac Bonneville 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
- 2000 Pontiac Bonneville 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:1
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Bonneville AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Bonneville cars and light trucks from 1990+.
Power Brake Units -> Adjustments -> AC-Delco Single Diaphragm Type -> AC-Delco Tandem Diaphragm Type -> Air Method -> Brake Pedal -> Gauge Method -> Pushrod -> Toyota/GM Single Diaphragm Type
Vehicle: 2000 Pontiac Bonneville 3.8 V6 GAS
Brake Pedal
Toyota/GM Single Diaphragm Type
- With engine running and brake pedal in rest position, measure distance between face of pedal and floor mat.
- Distance should be 5.850-6.244 inches.
- If distance is not as specified, adjust pedal height as follows:
- Remove lefthand lower instrument panel trim section and air duct.
- Loosen stop lamp switch sufficiently to access pedal adjustment.
- Loosen locknut and rotate pedal pushrod as required to obtain specified pedal height. Tighten locknut.
- Adjust brake lamp switch position so plunger lightly contacts pedal stopper and brake lamps are off when pe...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Bonneville BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Bonneville AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Bonneville cars and light trucks from 1990+.
Power Brake Units -> Application Chart
Vehicle: 2000 Pontiac Bonneville 3.8 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Bonneville BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Bonneville AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Bonneville cars and light trucks from 1990+.
Anti-lock Brakes -> Delco/Bosch Type 5.3 -> System Service -> Aurora, DeVille & Seville -> Auto Bleed -> Bonneville, LeSabre & Park Avenue -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> Electronic Brake Control Module (EBCM) -> Lateral Accelerometer Sensor -> Manual Bleed -> Pressure Bleed -> Wheel Speed Sensor -> Yaw Rate Sensor
Vehicle: 2000 Pontiac Bonneville 3.8 V6 GAS
Brake System Bleed
Auto Bleed
Perform manual or pressure bleeding as outlined under " Manual Bleed" or "Pressure Bleed" before auto bleeding system
- Turn ignition switch to Off position.
- Raise and support vehicle, then remove all tire and wheel assemblies.
- Inspect brake system for leaks and damage.
- Ensure battery is fully charged.
- Connect suitable programmed scan tool to Data Link Connector (DLC) located on lefthand side of instrument panel below steering column.
- Turn ignition switch to On position. Do not start engine.
- Establish scan tool communications by selecting ABS/TCS, Special Functions...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Bonneville BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Bonneville AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Bonneville cars and light trucks from 1990+.
Drum Brakes -> Type 5 -> Brake Service -> Installation -> Removal
Vehicle: 2000 Pontiac Bonneville 3.8 V6 GAS
Removal
- Raise and support vehicle.
- Mark relationship of wheel to axle, then remove wheel and tire assembly.
- Remove brake drum. If drum is difficult to remove, proceed as follows:
- Ensure parking brake is released.
- Back off parking brake cable adjustment.
- Remove access hole plug from backing plate, insert screwdriver through hole and push parking brake lever off its stop.
- Insert punch through hole in splash shield Fig. , tap on punch to loosen drum, then remove drum.
- Remove actuator spring using brake tool No. J-38400, or equivalent to pry loop end of spring from adjuster actuator, Fig. . D...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Bonneville BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Bonneville AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Bonneville cars and light trucks from 1990+.
Drum Brakes -> Type 5 -> Description
Vehicle: 2000 Pontiac Bonneville 3.8 V6 GAS
This brake assembly operates with fewer components, but is equal to other drum brake systems in performance. In this assembly,...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Bonneville BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Bonneville AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Bonneville cars and light trucks from 1990+.
Drum Brakes -> Type 5 -> Adjustments -> Parking Brake -> Service Brake
Vehicle: 2000 Pontiac Bonneville 3.8 V6 GAS
Service Brake
- Raise and support vehicle.
- Mark relationship of wheel to axle, then remove wheel and tire assembly.
- Remove brake drum. If drum is difficult to remove, proceed as follows:
- Ensure parking brake is released.
- Back off parking brake cable adjustment.
- Remove access hole plug from backing plate, insert screwdriver through hole and push parking brake lever off its stop.
- Insert punch through hole in splash shield, Fig. , tap on punch to loosen drum, then remove drum.
- Measure inside diameter of drum using tool Nos. J-21177-A or J-22364-01, or their equivalents.
- Adjust by turning star whe...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Bonneville BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Pontiac Bonneville vehicle.
|
| Access the Complete guide! |
