Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Audi 200 car and truck
repair procedures including Audi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Audi 200 automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1990 Audi 200 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Audi 200 cars and light trucks from 1990+.
AUDI, POWER BRAKE UNITS -> BRAKE BOOSTER, CHECKING -> 80/90
Vehicle: 1990 Audi 200 2.2 L5 GAS
80/90
- Depress brake pedal firmly approximately 20 times with engine Off.
- Depress brake...
CLICK HERE TO GET FULL ACCESS TO 1990 Audi 200 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Audi 200 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Audi 200 cars and light trucks from 1990+.
AUDI, HYDRAULIC BRAKE SYSTEM -> PROPORTIONING VALVE, CHECKING -> 80/90
Vehicle: 1990 Audi 200 2.2 L5 GAS
80/90
The proportioning valve is located under the brake booster.
- Lift vehicle, then attach VW 1310 or equivalent, to left front and left rear brake calipers, then bleed gauges.
- Depress brake pedal until gauge on front caliper reads 725 psi. G...
CLICK HERE TO GET FULL ACCESS TO 1990 Audi 200 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Audi 200 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Audi 200 cars and light trucks from 1990+.
AUDI, HYDRAULIC BRAKE SYSTEM -> HEIGHT SENSITIVE BRAKE PRESSURE REGULATOR -> 80/90 -> ADJUSTING -> CHECKING -> PRESSURE CHECK
Vehicle: 1990 Audi 200 2.2 L5 GAS
CHECKING
80/90
Brake pressure regulator is mounted on right rear of body and operated by spring attached to rear axle. Test must be conducted with empty vehicle, full fuel tank and driver's seat occupied.
- Firmly depress pedal once (vehicle must be on ground).
- Release pedal suddenly and ensure lever on pressure regulator moves.
PRESSURE CHECK
80/90
- Ensure brake system is properly filled and bled.
- Connect gauge assembly US 1016 or equivalent, to left front and right rear calipers, according to manufacturer's instructions.
- On 90 models, bounce vehicle several times...
CLICK HERE TO GET FULL ACCESS TO 1990 Audi 200 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Audi 200 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Audi 200 cars and light trucks from 1990+.
AUDI, DISC BRAKES -> Audi Dual Piston w/Dual Mounting Bolts, Front -> BRAKE PADS REPLACEMENT
Vehicle: 1990 Audi 200 2.2 L5 GAS
- Raise and support vehicle, then remove front wheels.
- Pull plug connector for wear indicator out of clip, then press connector on knurled surface and pull apart.
- Using open end wrench to hold guide pin head, remove lower caliper mounting bolt.
- Swing caliper upward, then remove brake pads.
- Place an old brake pad into caliper and push piston back into caliper housing. Always remove some brake fluid from master cylinder reservoir prior to installing new pads. When calip...
CLICK HERE TO GET FULL ACCESS TO 1990 Audi 200 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Audi 200 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Audi 200 cars and light trucks from 1990+.
AUDI, HYDRAULIC BRAKE SYSTEM -> BRAKE PRESSURE REGULATOR -> 100/200 Quattro Models -> 1990-91 100 -> 1990-91 100/200 -> 1992 100 -> ADJUSTING -> CHECKING -> V8 Quattro
Vehicle: 1990 Audi 200 2.2 L5 GAS
CHECKING
1990-91 100/200
Brake pressure regulator is mounted on body (left rear), and operated by a spring attached to the rear axle.
- Firmly depress brake pedal once, with car on the ground.
- Release pedal suddenly and ensure lever on pressure regulator moves.
- Raise and support vehicle to remove load from rear axle.
- Press brake pressure regulator lever toward rear.
- Loosen nut from front of spring, then attach spring, without play or tension, to plastic roller.
- Torque nut to 18 ft. lbs.
1992 100
Brake pressure regulator is mounted on body (left rear), and operated by a spring attac...
CLICK HERE TO GET FULL ACCESS TO 1990 Audi 200 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Audi 200 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Audi 200 cars and light trucks from 1990+.
AUDI, HYDRAULIC BRAKE SYSTEM -> MASTER CYLINDER REPLACEMENT
Vehicle: 1990 Audi 200 2.2 L5 GAS
Refer to Figs. through , when replacing master cylinder.
- Disconnect brake lines from master cylinder.
- R...
CLICK HERE TO GET FULL ACCESS TO 1990 Audi 200 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1990 Audi 200 vehicle.
|
| Access the Complete guide! |
