Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Jeep Wrangler car and truck
repair procedures including Jeep engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Jeep Wrangler automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1990 Jeep Wrangler
- 1990 Jeep Wrangler 2.5 L4 GAS, CID:150, Fuel Injection, Aspiration:150, Engine VIN:, Desg:E
- 1990 Jeep Wrangler 4.2 L6 GAS, CID:258, Carburetor, Aspiration:258, Engine VIN:, Desg:T
- 1990 Jeep Wrangler Laredo 4.2 L6 GAS, CID:258, Carburetor, Aspiration:258, Engine VIN:, Desg:T
- 1990 Jeep Wrangler Islander 2.5 L4 GAS, CID:150, Fuel Injection, Aspiration:150, Engine VIN:, Desg:E
- 1990 Jeep Wrangler Islander 4.2 L6 GAS, CID:258, Carburetor, Aspiration:258, Engine VIN:, Desg:T
- 1990 Jeep Wrangler Sahara 2.5 L4 GAS, CID:150, Fuel Injection, Aspiration:150, Engine VIN:, Desg:E
- 1990 Jeep Wrangler Sahara 4.2 L6 GAS, CID:258, Carburetor, Aspiration:258, Engine VIN:, Desg:T
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Jeep Wrangler AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Jeep Wrangler cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Jeep Wrangler 4.2 L6 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate if equipped to gain access to propeller shaft.
- Mark a line across axle pinion flange, propeller shaft, flange yoke and transfer case for installation reference.
- Remove U-joint strap bolts at pinion shaft yoke.
- Remove transfer case yoke bolts.
- Push rear of propeller shaft forward to clear transfer case yoke.
- Remove propeller shaft from vehicle.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque U-joint strap bolts t...
CLICK HERE TO GET FULL ACCESS TO 1990 Jeep Wrangler DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Jeep Wrangler AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Jeep Wrangler cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace
Vehicle: 1990 Jeep Wrangler 2.5 L4 GAS
Clamp only the narrow forged portion of the yoke in the vise. Failure to heed caution may result in damage.
- Remove axle shaft.
- Remove bearing cap retaining snap rings. Saturate the bearing caps with penetrating oil prior to removal.
- Place socket (receiver) with inside diameter larger than bearing cap against yoke and perimeter of bearing cap to be removed.
- Pla...
CLICK HERE TO GET FULL ACCESS TO 1990 Jeep Wrangler DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Jeep Wrangler AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Jeep Wrangler cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace
Vehicle: 1990 Jeep Wrangler Islander 4.2 L6 GAS
Clamp only the narrow forged portion of the yoke in the vise. Failure to heed caution may result in damage.
- Remove axle shaft.
- Remove bearing cap retaining snap rings. Saturate the bearing caps with penetrating oil prior to removal.
- Place socket (receiver) with inside diameter larger than bearing cap against yoke and perimeter of bearing cap to be removed.
- Pla...
CLICK HERE TO GET FULL ACCESS TO 1990 Jeep Wrangler DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Jeep Wrangler AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Jeep Wrangler cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Jeep Wrangler Islander 4.2 L6 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate if equipped to gain access to propeller shaft.
- Mark a line across axle pinion flange, propeller shaft, flange yoke and transfer case for installation reference.
- Remove U-joint strap bolts at pinion shaft yoke.
- Remove transfer case yoke bolts.
- Push rear of propeller shaft forward to clear transfer case yoke.
- Remove propeller shaft from vehicle.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque U-joint strap bolts t...
CLICK HERE TO GET FULL ACCESS TO 1990 Jeep Wrangler DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Jeep Wrangler AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Jeep Wrangler cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Jeep Wrangler Sahara 2.5 L4 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate if equipped to gain access to propeller shaft.
- Mark a line across axle pinion flange, propeller shaft, flange yoke and transfer case for installation reference.
- Remove U-joint strap bolts at pinion shaft yoke.
- Remove transfer case yoke bolts.
- Push rear of propeller shaft forward to clear transfer case yoke.
- Remove propeller shaft from vehicle.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque U-joint strap bolts t...
CLICK HERE TO GET FULL ACCESS TO 1990 Jeep Wrangler DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Jeep Wrangler AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Jeep Wrangler cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Jeep Wrangler Laredo 4.2 L6 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate if equipped to gain access to propeller shaft.
- Mark a line across axle pinion flange, propeller shaft, flange yoke and transfer case for installation reference.
- Remove U-joint strap bolts at pinion shaft yoke.
- Remove transfer case yoke bolts.
- Push rear of propeller shaft forward to clear transfer case yoke.
- Remove propeller shaft from vehicle.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque U-joint strap bolts t...
CLICK HERE TO GET FULL ACCESS TO 1990 Jeep Wrangler DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
