Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1991 Toyota Cressida car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1991 Toyota Cressida automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1991 Toyota Cressida
- 1991 Toyota Cressida Luxury 3.0 L6 GAS, CC:2954, Fuel Injection, Engine VIN:, Desg:M
- 1991 Toyota Cressida 3.0 L6 GAS, CC:2954, Fuel Injection, Engine VIN:, Desg:M
BRAKE SERVICE PROCEDURES FOR 1991 Toyota Cressida AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Toyota Cressida cars and light trucks from 1990+.
TOYOTA, HYDRAULIC BRAKES -> MASTER CYLINDER -> Assembly -> Disassembly -> Except Van -> Inspection -> OVERHAUL -> REPLACE -> Van
Vehicle: 1991 Toyota Cressida 3.0 L6 GAS
REPLACE
Except Van
- On MR2, remove luggage compartment trim cover by removing two clips after disengaging inner part of clip.
- On all models, label, disconnect brake lines using line wrench 09751-36011, or equivalent. Then cap brake lines from master cylinder.
- Disconnect wire connector from brake pressure switch and then disconnect level warning switch connector, if equipped.
- Remove master cylinder to brake unit attaching nuts, then remove master cylinder, wire clamp, gasket and 3-way union, as needed.
- Reverse procedure to install. Bleed brake system.
Van
- Disconnect battery ground cable
- Re...
CLICK HERE TO GET FULL ACCESS TO 1991 Toyota Cressida BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Toyota Cressida AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Toyota Cressida cars and light trucks from 1990+.
TOYOTA, HYDRAULIC BRAKES -> PROPORTIONING VALVE REPLACEMENT -> EXCEPT LAND CRUISER, PICKUP, 4RUNNER & VAN -> LAND CRUISER, PICKUP, 4RUNNER & VAN -> Models w/Load Sensing Proportioning Valve (LSPV) -> Models w/Proportioning & By-Pass Valve (P-BV)
Vehicle: 1991 Toyota Cressida Luxury 3.0 L6 GAS
EXCEPT LAND CRUISER, PICKUP, 4RUNNER & VAN
Models w/Load Sensing Proportioning Valve (LSPV)
- Disconnect brake lines using line wrench 09751-36011, or equivalent.
- Remove proportioning valve adjusting nut, then the spring from rear suspension arm.
- Remove bolts and proportioning valve from mounting assembly.
- Reverse procedure to install. Bleed brakes.
Models w/Proportioning & By-Pass Valve (P-BV)
The prop...
CLICK HERE TO GET FULL ACCESS TO 1991 Toyota Cressida BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Toyota Cressida AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Toyota Cressida cars and light trucks from 1990+.
TOYOTA, ANTI-LOCK BRAKES -> COMPONENT TESTING -> 1990-91 Celica & 1992 Camry -> 1992 Celica -> ANTI-LOCK BRAKE SYSTEM CIRCUIT CHECK -> BRAKE ACTUATOR -> CONTROL RELAYS -> DECELERATION SENSOR OPERATION DIAGNOSIS SYSTEM (DSODS) -> Except 1990-92 Celica, Pickup & 4Runner & 1992 Camry -> FRONT SPEED SENSOR -> Pickup & 4Runner -> REAR SPEED SENSOR -> SPEED SENSOR DIAGNOSTIC SYSTEM
Vehicle: 1991 Toyota Cressida Luxury 3.0 L6 GAS
SPEED SENSOR DIAGNOSTIC SYSTEM
While checking the speed sensor diagnosis system, the ABS does not function and the brakes function as a standard brake system.
- Ensure the battery voltage is approximately 12 volts and the "ANTI-LOCK" warning light is functioning.
- On 1990-91 Celica 2WD models, remove control relay, then disconnect the check connector from the control relay.
- On 1990-91 Celica 4WD and Camry models, remove the rubber cap from the Ts connector then, connect the terminals.
- On Celica 2WD models, disconnect the check connector from the actuator.
- On Cressida models, connect the ...
CLICK HERE TO GET FULL ACCESS TO 1991 Toyota Cressida BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Toyota Cressida AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Toyota Cressida cars and light trucks from 1990+.
TOYOTA, POWER BRAKE UNITS -> BRAKE BOOSTER REPLACEMENT -> Cressida -> Except Cressida -> INSTALLATION -> REMOVAL
Vehicle: 1991 Toyota Cressida Luxury 3.0 L6 GAS
REMOVAL
Except Cressida
- On models with airbag, disable airbag system as described under "Airbag System Disarming."
- On models less airbag, disconnect battery ground cable.
- On all models, remove master cylinder as outlined under "Master Cylinder, Replace" in the "Hydraulic Brake System" section.
- On 1992 Camry and Celica models, push away charcoal vapor canister for better access.
- On Supra, remove cruise actuator.
- On Supra and 1992 Celica models, remove lower finish panel or lower pad as outlined in "Dash Panel Service."
- Remove pedal return spring, clip, clevis pin and clevis locknut, Fi...
CLICK HERE TO GET FULL ACCESS TO 1991 Toyota Cressida BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Toyota Cressida AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Toyota Cressida cars and light trucks from 1990+.
TOYOTA, DRUM BRAKES -> APPLICATION CHART
Vehicle: 1991 Toyota Cressida Luxury 3.0 L6 GAS
CLICK HERE TO GET FULL ACCESS TO 1991 Toyota Cressida BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Toyota Cressida AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Toyota Cressida cars and light trucks from 1990+.
TOYOTA, POWER BRAKE UNITS -> BRAKE BOOSTER OPERATIONAL TEST -> AIR TIGHTNESS CHECK -> OPERATING CHECK
Vehicle: 1991 Toyota Cressida Luxury 3.0 L6 GAS
OPERATING CHECK
- Depress brake pedal several times with engine stopped, and ensure that pedal reserve distance has no change, Fig. .
- Depress brake pedal and start engine. If pedal drops slightly, operation is normal.
AIR TIGHTNESS CHECK
- Start engine and stop after one or two minutes.
- Depress brake pedal sever...
CLICK HERE TO GET FULL ACCESS TO 1991 Toyota Cressida BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1991 Toyota Cressida vehicle.
|
| Access the Complete guide! |
