Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 Audi 100 Quattro car and truck
repair procedures including Audi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1993 Audi 100 Quattro automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1993 Audi 100 Quattro
- 1993 Audi 100 Quattro CS 2.8 V6 GAS, CC:2771, Fuel Injection, Engine VIN:, Desg:J
- 1993 Audi 100 Quattro CS 2.8 V6 GAS, CC:2771, Fuel Injection, Engine VIN:, Desg:K
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Audi 100 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 Audi 100 Quattro cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1993 Audi 100 Quattro CS 2.8 V6 GAS
Driveshaft work must be performed with vehicle on a suitable dual support hoist.
- Remove catalytic converter, then tie exhaust pipe to left side of vehicle with wire.
- Remove support, if required, then loosen propeller shaft bolts at transmission, differential and center support.
- Ensure white dot on rear propeller shaft flange aligned with a black dot on differential flange. If not, scribe mark on propeller shaft and differential flanges prior to disassembly.
- Install a suitable alignment tool on driveshaft and tighten plastic nuts.
- Remove propeller shaft bolts at transmission and d...
CLICK HERE TO GET FULL ACCESS TO 1993 Audi 100 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Audi 100 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 Audi 100 Quattro cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1993 Audi 100 Quattro CS 2.8 V6 GAS
Driveshaft work must be performed with vehicle on a suitable dual support hoist.
- Remove catalytic converter, then tie exhaust pipe to left side of vehicle with wire.
- Remove support, if required, then loosen propeller shaft bolts at transmission, differential and center support.
- Ensure white dot on rear propeller shaft flange aligned with a black dot on differential flange. If not, scribe mark on propeller shaft and differential flanges prior to disassembly.
- Install a suitable alignment tool on driveshaft and tighten plastic nuts.
- Remove propeller shaft bolts at transmission and d...
CLICK HERE TO GET FULL ACCESS TO 1993 Audi 100 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Audi 100 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 Audi 100 Quattro cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1993 Audi 100 Quattro CS 2.8 V6 GAS
- Remove wheel cover and remove nut securing axle shaft in hub.
- Raise and support vehicle, then remove wheels. Remove shield in right side driveshaft.
- Remove driveshaft flange to transmission securing screws, then pull speed sensor slightly out of housing.
- On automatic transmission models, remove stabilizer bar clamps and disconnect ball joint from hub.
- On all models, press axle shaft from hub using a suitable hub puller.
- Raise transmission en...
CLICK HERE TO GET FULL ACCESS TO 1993 Audi 100 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Audi 100 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 Audi 100 Quattro cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1993 Audi 100 Quattro CS 2.8 V6 GAS
- Remove wheel cover and remove nut securing axle shaft in hub.
- Raise and support vehicle, then remove wheels. Remove shield in right side driveshaft.
- Remove driveshaft flange to transmission securing screws, then pull speed sensor slightly out of housing.
- On automatic transmission models, remove stabilizer bar clamps and disconnect ball joint from hub.
- On all models, press axle shaft from hub using a suitable hub puller.
- Raise transmission en...
CLICK HERE TO GET FULL ACCESS TO 1993 Audi 100 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1993 Audi 100 Quattro vehicle.
|
| Access the Complete guide! |
