Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1994 Oldsmobile 98 car and truck
repair procedures including Oldsmobile engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1994 Oldsmobile 98 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1994 Oldsmobile 98
- 1994 Oldsmobile 98 Regency 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:L
- 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:L
- 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:1
BRAKE SERVICE PROCEDURES FOR 1994 Oldsmobile 98 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Oldsmobile 98 cars and light trucks from 1990+.
Drum Brakes -> Type 8 -> Brake Service -> INSTALLATION -> REMOVAL
Vehicle: 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS
REMOVAL
- Raise and support vehicle.
- Mark relationship of wheel to axle, then remove wheel and tire assembly.
- Remove brake drum. If drum is difficult to remove, proceed as follows:
- Ensure parking brake is released.
- Back off parking brake cable adjustment.
- Remove access hole plug from backing plate, insert screwdriver through hole and push parking brake lever off its stop.
- Insert punch through hole in splash shield Fig. , tap on punch to loosen drum. Then remove drum.
- Remove actuator spring using special brake tool J 38400 or equivalent to pry loop end of spring from adjuster actuator, Fig. ...
CLICK HERE TO GET FULL ACCESS TO 1994 Oldsmobile 98 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Oldsmobile 98 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Oldsmobile 98 cars and light trucks from 1990+.
Power Brake Units -> Precautions
Vehicle: 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS
- After disassembling a power brake unit, soak all metal parts in solvent.
- Use only alcohol on parts containing rubber. After the parts have been thoroughly cleaned and rinsed in solvent, they should be rewashed in clean alcohol before assembling.
- Use compressed air to blow dirt and cleaning fluid from the recesses and internal passages.
- Always use ...
CLICK HERE TO GET FULL ACCESS TO 1994 Oldsmobile 98 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Oldsmobile 98 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Oldsmobile 98 cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> AC-DELCO TANDEM DIAPHRAGM TYPE -> Assemble -> Assembly -> BCIA SINGLE DIAPHRAGM TYPE -> BCIA TANDEM DIAPHRAGM TYPE -> Disassemble -> Disassembly -> GEO METRO SINGLE DIAPHRAGM TYPE -> OVERHAUL -> TOYOTA/GM SINGLE DIAPHRAGM TYPE
Vehicle: 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS
AC-DELCO TANDEM DIAPHRAGM TYPE
OVERHAUL
Disassemble
- Remove pedal pushrod boot, silencer, check valve, vacuum switch and grommets, as equipped, then the front housing seal.
- Scribe matching marks between front and rear housing sections, then mount booster assembly in suitable holding fixture with rear housing facing up.
- Apply pressure to housing with holding fixture forcing screw and rotate rear housing counterclockwise to unlock housing halves.
- Slowly release spring tension, then remove booster assembly from holding fixture. Do not allow spring tension to release suddenly, as ...
CLICK HERE TO GET FULL ACCESS TO 1994 Oldsmobile 98 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Oldsmobile 98 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Oldsmobile 98 cars and light trucks from 1990+.
Power Brake Units -> Troubleshooting -> AC-DELCO TANDEM DIAPHRAGM TYPE -> BCIA SINGLE & TANDEM DIAPHRAGM TYPE -> Brakes Drag -> Brakes Grab -> Brakes Slow To Release Or Drag -> Brakes Slow To Respond -> Excessive Pedal Effort -> Hard Pedal -> Hard Pedal/Brakes Inefficient -> Low Or Spongy Brake Pedal -> Slow Or No Release -> TOYOTA/GM SINGLE DIAPHRAGM TYPE
Vehicle: 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS
AC-DELCO TANDEM DIAPHRAGM TYPE
Hard Pedal
- Internal vacuum leak.
- Faulty control valve.
Brakes Grab
- Faulty control valve.
Slow Or No Release
- Faulty pushrod adjustment.
- Bind in linkage.
BCIA SINGLE & TANDEM DIAPHRAGM TYPE
Brakes Grab
- Internal vacuum leak.
- Faulty control valve
Excessive Pedal Effort
- Leak in booster vacuum supply.
- Glazed linings.
- Contaminated brake fluid.
- Restricted filter or booster valve air passage.
- Leak in booster vacuum supply.
- Damaged booster or improperly assembled booster valve.
Brakes Slow To Respond
- Restricted filter or booster valve air passage.
- Contaminated brake fluid.
- Leak in...
CLICK HERE TO GET FULL ACCESS TO 1994 Oldsmobile 98 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Oldsmobile 98 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Oldsmobile 98 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Diagnosis & Testing
Vehicle: 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS
Refer to...
CLICK HERE TO GET FULL ACCESS TO 1994 Oldsmobile 98 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Oldsmobile 98 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Oldsmobile 98 cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Front Disc Brake (Type 2) -> Brake Pad Service -> INSTALLATION -> REMOVAL
Vehicle: 1994 Oldsmobile 98 Regency Elite 3.8 V6 GAS
REMOVAL
- Remove caliper assembly as described in "Caliper Service."
- Remove shoe and lining assemblies from caliper, Figs. through , noting the following:
- On models with tab mount outer shoe (all except series 3264), straighten bent over shoe tabs with suitable pliers.
- On models with spring mount outer shoe (series 3264), insert screwdriver between shoe and caliper and disengage buttons on shoe from holes in caliper.
- Remove sleeves and bushings from grooves in caliper mounting bolt holes, Figs. through .
INSTALLATION
- Lubricate new bushings with suitable grease, install bushings in cali...
CLICK HERE TO GET FULL ACCESS TO 1994 Oldsmobile 98 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
