Auto Parts Search
We have info for following modifications of 1996 Jeep Cherokee
- 1996 Jeep Cherokee Sport 4.0 L6 GAS, CID:242, Fuel Injection, Aspiration:242, Engine VIN:, Desg:S
- 1996 Jeep Cherokee Country 4.0 L6 GAS, CID:242, Fuel Injection, Aspiration:242, Engine VIN:, Desg:S
- 1996 Jeep Cherokee SE 2.5 L4 GAS, CID:150, Fuel Injection, Aspiration:150, Engine VIN:, Desg:P
- 1996 Jeep Cherokee SE 4.0 L6 GAS, CID:242, Fuel Injection, Aspiration:242, Engine VIN:, Desg:S
- 1996 Jeep Cherokee Classic 4.0 L6 GAS, CID:242, Fuel Injection, Aspiration:242, Engine VIN:, Desg:S
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Jeep Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Jeep Cherokee cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1996 Jeep Cherokee SE 2.5 L4 GAS
Front
- Hoist and support vehicle on safety stands.
- Scribe alignment marks on yokes at transfer case. Place marks at pinion shaft and at each end of propeller shaft. These marks will be used for installation reference.
- Remove universal joint strap bolts at pinion shaft yoke.
- Disconnect propeller shaft at transfer case and remove propeller shaft.
- Reverse procedure to install, noting the following:
- Torque universal joint strap/clamp bolts at axle yoke to 14 ft. lbs.
- Torque flange to transfer case bolts to 20 ft. lbs.
Rear
- Shif...
CLICK HERE TO GET FULL ACCESS TO 1996 Jeep Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Jeep Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Jeep Cherokee cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1996 Jeep Cherokee Classic 4.0 L6 GAS
Front
- Hoist and support vehicle on safety stands.
- Scribe alignment marks on yokes at transfer case. Place marks at pinion shaft and at each end of propeller shaft. These marks will be used for installation reference.
- Remove universal joint strap bolts at pinion shaft yoke.
- Disconnect propeller shaft at transfer case and remove propeller shaft.
- Reverse procedure to install, noting the following:
- Torque universal joint strap/clamp bolts at axle yoke to 14 ft. lbs.
- Torque flange to transfer case bolts to 20 ft. lbs.
Rear
- Shif...
CLICK HERE TO GET FULL ACCESS TO 1996 Jeep Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Jeep Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Jeep Cherokee cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1996 Jeep Cherokee Sport 4.0 L6 GAS
Front
- Hoist and support vehicle on safety stands.
- Scribe alignment marks on yokes at transfer case. Place marks at pinion shaft and at each end of propeller shaft. These marks will be used for installation reference.
- Remove universal joint strap bolts at pinion shaft yoke.
- Disconnect propeller shaft at transfer case and remove propeller shaft.
- Reverse procedure to install, noting the following:
- Torque universal joint strap/clamp bolts at axle yoke to 14 ft. lbs.
- Torque flange to transfer case bolts to 20 ft. lbs.
Rear
- Shif...
CLICK HERE TO GET FULL ACCESS TO 1996 Jeep Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Jeep Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Jeep Cherokee cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan Joint -> Single Cardan Joint
Vehicle: 1996 Jeep Cherokee Sport 4.0 L6 GAS
Single Cardan Joint
Disassemble
Individual components of cardan universal joints are not serviceable. If worn or leaking, they must be replaced as an assembly.
- Remove propeller shaft.
- Using a soft drift, tap outside of bearing cap assembly to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Set yoke in an arbor press or vise with a socket whose inside diameter is large enough to receive bearing cap positioned beneath yoke.
- Position yoke with grease fitting, if equipped, pointing up.
- Place a socket with an outside diameter smaller than upper bearing cap on upper b...
CLICK HERE TO GET FULL ACCESS TO 1996 Jeep Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Jeep Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Jeep Cherokee cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan Joint -> Single Cardan Joint
Vehicle: 1996 Jeep Cherokee Country 4.0 L6 GAS
Single Cardan Joint
Disassemble
Individual components of cardan universal joints are not serviceable. If worn or leaking, they must be replaced as an assembly.
- Remove propeller shaft.
- Using a soft drift, tap outside of bearing cap assembly to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Set yoke in an arbor press or vise with a socket whose inside diameter is large enough to receive bearing cap positioned beneath yoke.
- Position yoke with grease fitting, if equipped, pointing up.
- Place a socket with an outside diameter smaller than upper bearing cap on upper b...
CLICK HERE TO GET FULL ACCESS TO 1996 Jeep Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Jeep Cherokee AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Jeep Cherokee cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan Joint -> Single Cardan Joint
Vehicle: 1996 Jeep Cherokee SE 2.5 L4 GAS
Single Cardan Joint
Disassemble
Individual components of cardan universal joints are not serviceable. If worn or leaking, they must be replaced as an assembly.
- Remove propeller shaft.
- Using a soft drift, tap outside of bearing cap assembly to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Set yoke in an arbor press or vise with a socket whose inside diameter is large enough to receive bearing cap positioned beneath yoke.
- Position yoke with grease fitting, if equipped, pointing up.
- Place a socket with an outside diameter smaller than upper bearing cap on upper b...
CLICK HERE TO GET FULL ACCESS TO 1996 Jeep Cherokee DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1996 Jeep Cherokee vehicle. |
Access the Complete guide! |