Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1998 KIA Sportage AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 KIA Sportage cars and light trucks from 1990+.
Anti-lock Brakes -> Sportage -> System Service -> 1997 -> 1998-2001 -> 2002 -> Brake System Bleed -> Component Replacement -> Electronic Control Unit -> Front Wheel Speed Sensor -> Rear Wheel Speed Sensor
Vehicle: 1998 KIA Sportage 2.0 L4 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for brake bleeding procedure.
Component Replacement
Electronic Control Unit
1997
- Disconnect ABS Electronic Control Unit (ECU) harness electrical connector.
- Remove lower instrument panel trim panel below steering column. Trim panel screws are accessed by removing two square screw covers.
- Remove ABS ECU mounting screws, Fig. , then the ECU.
- Reverse procedure to install.
1998-2001
- Disconnect ECU electrical connectors.
- Remove ECU bracket to fender mounting nuts.
- Remove ECU to HCU mounting bolts.
- Lift ECU straight up, then disconnect motor electri...
CLICK HERE TO GET FULL ACCESS TO 1998 KIA Sportage BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 KIA Sportage AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 KIA Sportage cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> Brake Pedal -> Rio, Sephia & Spectra -> Sedona -> Sportage
Vehicle: 1998 KIA Sportage 2.0 L4 GAS
Brake Pedal
Rio, Sephia & Spectra
- On Rio models, distance from top center of brake pedal to floor mat should be 6.69-6.93 inches.
- On Sephia and Spectra models, distance from top center of brake pedal to floor mat should be 7.60-7.72 inches.
- On all models, disconnect brake pedal switch electrical connector (E), Fig. .
- Loosen locknuts (B) and turn switch (A) until it does not contact pedal.
- Loosen locknuts (D) and turn rod (C) to adjust height of brake pedal.
- Tighten brake pedal switch until plunger is completely compressed, then rotate additional 1/2 turn and tighten locknuts.
- Inspect operat...
CLICK HERE TO GET FULL ACCESS TO 1998 KIA Sportage BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 KIA Sportage AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 KIA Sportage cars and light trucks from 1990+.
Anti-lock Brakes -> Sportage -> Precautions
Vehicle: 1998 KIA Sportage 2.0 L4 GAS
Hydraulic brake fluid will damage painted surface...
CLICK HERE TO GET FULL ACCESS TO 1998 KIA Sportage BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 KIA Sportage AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 KIA Sportage cars and light trucks from 1990+.
Disc Brakes -> Brake System Bleed
Vehicle: 1998 KIA Sportage 2.0 L4 GAS
- Ensure brake fluid reservoir remains at least 3/4 full during entire bleed procedure.
- Raise and support vehicle.
- Remove bleeder cap at bleeder screw farthest from master cylinder and attach a vinyl hose to bleeder screw.
- Place other end of tube in a clear container filled with fresh brake flui...
CLICK HERE TO GET FULL ACCESS TO 1998 KIA Sportage BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 KIA Sportage AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 KIA Sportage cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder -> Rio -> Sedona -> Sephia & Spectra -> Sportage
Vehicle: 1998 KIA Sportage 2.0 L4 GAS
Hydraulic brake fluid will damage painted surfaces. If fluid gets on painted surface, wipe clean immediately.
Master Cylinder
Rio
- Remove master cylinder in numbered sequence, Fig. , noting the following:
- Disconnect brake lines from master cylinder and ABS control unit using flare nut wrench tool No. OK130 430 019, or equivalent.
- Plug all open lines and ports to prevent entry of dirt or debris.
- Reverse procedure to install, noting the following:
- Place adjustment gauge tool No. OK370 430 018, or equivalent, onto master cylinder, Fig. .
- Apply 19.7 inches of vacuum to booster unit usi...
CLICK HERE TO GET FULL ACCESS TO 1998 KIA Sportage BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 KIA Sportage AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 KIA Sportage cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder -> Rio -> Sephia -> Sportage -> Wheel Cylinder
Vehicle: 1998 KIA Sportage 2.0 L4 GAS
Master Cylinder
Rio
- Secure master cylinder assembly in a suitable vise.
- Remove reservoir cap, Fig. , then drain brake fluid into a suitable container.
- Remove level sensor using a suitable screwdriver.
- Remove reservoir mounting screw, then pry reservoir out of master cylinder. Discard seals.
- Push primary piston into cylinder bore to ease snap ring removal, then remove snap ring and piston.
- Push secondary piston into bore, then remove secondary piston stop screw.
- Place a suitable shop towel in bore to catch secondary piston.
- Remove secondary piston using compressed air through port.
- Rever...
CLICK HERE TO GET FULL ACCESS TO 1998 KIA Sportage BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 KIA Sportage vehicle. |
Access the Complete guide! |