Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Audi A8 Quattro car and truck
repair procedures including Audi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Audi A8 Quattro automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2000 Audi A8 Quattro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Audi A8 Quattro cars and light trucks from 1990+.
Disc Brakes -> Single Piston Rear Disc Brakes -> Tightening Specifications
Vehicle: 2000 Audi A8 Quattro 4.2 V8 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Audi A8 Quattro BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Audi A8 Quattro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Audi A8 Quattro cars and light trucks from 1990+.
Power Brake Units -> Diagnosis & Testing -> Hydraulic Booster/Servo -> Pressure Accumulator Check Valve -> Pressure Accumulator Pressure Relief Valve -> Pressure Accumulator-Gas Pressure -> Vacuum Booster
Vehicle: 2000 Audi A8 Quattro 4.2 V8 GAS
Hydraulic Booster/Servo
- With ignition Off, depress brake pedal approximately 20 times to reduce system pressure.
- Disconnect warning lamp switch electrical connector, then remove switch.
- Attach pressure gauge with hollow bolt and copper washers to brake servo unit. Attach thick copper washer between brake servo unit and banjo fitting and thin copper washer between hollow bolt and banjo fitting.
- Start engine and let idle until pressure gauge reading exceeds 2030 psi.
- If specified pressure is not reached, measure delivery rate of central hydraulic pump as follows:
- Turn ignition Off, ...
CLICK HERE TO GET FULL ACCESS TO 2000 Audi A8 Quattro BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Audi A8 Quattro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Audi A8 Quattro cars and light trucks from 1990+.
Disc Brakes -> Single Piston Rear Disc Brakes -> Brake Pad Service -> Except TT -> TT
Vehicle: 2000 Audi A8 Quattro 4.2 V8 GAS
Except TT
- Raise and support vehicle, then remove wheel assemblies.
- If brake pads are to be used again, mark installed positions for installation reference.
- Remove caliper housing to carrier mounting bolts, then the caliper housing, Fig. .
- Remove brake pads from carrier.
- Extract part of brake fluid from reservoir using a suitable bleeder bottle, then install piston using installation tool No. 3272, or equivalent.
- Install brake pads, then the caliper housing and tighten to specifications.
- Install wheel assemblies and lower vehicle.
- On A4 and A8 models, depress brake pedal firmly several...
CLICK HERE TO GET FULL ACCESS TO 2000 Audi A8 Quattro BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Audi A8 Quattro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Audi A8 Quattro cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 2000 Audi A8 Quattro 4.2 V8 GAS
The following procedure has been modified by a Technical Service Bulletin.
To bleed brake system, use a catch bottle with a transparent hose attached so brake fluid can be inspected for air bubbles.
- Connect brake pressure bleeding tool No. VAG 1869, or equivalent, per tool manufacturer's instructions.
- Bleed brakes in following sequence:
- Righ...
CLICK HERE TO GET FULL ACCESS TO 2000 Audi A8 Quattro BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Audi A8 Quattro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Audi A8 Quattro cars and light trucks from 1990+.
Hydraulic Brake Systems -> Diagnosis & Testing -> A4, S4 & TT -> A6 & S6 -> Brake Pressure Regulator -> Cabriolet
Vehicle: 2000 Audi A8 Quattro 4.2 V8 GAS
Brake Pressure Regulator
A4, S4 & TT
On these models there is no mechanical brake pressure regulator. Specially matched control module software controls brake pressure regulation.
A6 & S6
Brake pressure regulator is mounted on body (lefthand rear), and operated by a spring attached to the rear axle. Prior to inspection, ensure system is properly bled and filled.
- Firmly depress brake pedal once, with vehicle on ground.
- Release pedal suddenly and ensure lever on pressure regulator moves.
Cabriolet
Brake pressure regulator is mounted on righthand rear of body and operated by spring att...
CLICK HERE TO GET FULL ACCESS TO 2000 Audi A8 Quattro BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Audi A8 Quattro AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Audi A8 Quattro cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> A4 & S4 -> A4, A6, S4 & S6 -> A6 & S6 -> A6, Cabriolet & S6 -> A8 -> Brake System Bleed -> Cabriolet -> Component Replacement -> Electronic Control Unit -> Front Wheel Speed Sensors -> Hydraulic Control Unit -> Hydraulic Control Unit Mounting Bracket -> Rear Wheel Speed Sensors -> TT
Vehicle: 2000 Audi A8 Quattro 4.2 V8 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for procedures.
Component Replacement
Electronic Control Unit
A4, A6, S4 & S6
The electronic control unit is located beneath the lefthand side of the rear seat.
- Turn ignition Off.
- Remove rear seat.
- Remove spring retaining electrical connector, then disconnect electrical connector.
- Remove screws securing control unit.
- Reverse procedure to install.
A8
- Remove lower slot cover from between knee bolster and lower column cover.
- Remove knee bolster.
- Remove ABS control module.
- Disconnect ABS control module electrical harness connector.
- Reverse procedure...
CLICK HERE TO GET FULL ACCESS TO 2000 Audi A8 Quattro BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Audi A8 Quattro vehicle.
|
| Access the Complete guide! |
