Auto Parts Search
We have info for following modifications of 2003 Ford F-350 Super Duty Pickup
- 2003 Ford F-350 Super Duty Pickup 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:L
- 2003 Ford F-350 Super Duty Pickup 7.3 V8 DIESEL, CID:445, Fuel Injection, Aspiration:445, Engine VIN:, Desg:F
- 2003 Ford F-350 Super Duty Pickup 6.8 V10 GAS, CID:415, Fuel Injection, Aspiration:415, Engine VIN:, Desg:S
- 2003 Ford F-350 Super Duty Pickup 6.0 V8 DIESEL, CID:363, Fuel Injection, Aspiration:363, Engine VIN:, Desg:P
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Ford F-350 Super Duty Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Ford F-350 Super Duty Pickup cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2003 Ford F-350 Super Duty Pickup 6.8 V10 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 26 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford F-350 Super Duty Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Ford F-350 Super Duty Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Ford F-350 Super Duty Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2003 Ford F-350 Super Duty Pickup 5.4 V8 GAS
Front
Warning: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the righthand kick panel area. Failure to do so can result in unexpected inflation or deflation of the air springs, which can result in shifting of the vehicle during these operations.
- With vehicle in NEUTRAL, position on a hoist.
- Remove the front wheel and tire assembly.
- Remove dust cap and nut from axle halfsha...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford F-350 Super Duty Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Ford F-350 Super Duty Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Ford F-350 Super Duty Pickup cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2003 Ford F-350 Super Duty Pickup 5.4 V8 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 15 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford F-350 Super Duty Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Ford F-350 Super Duty Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Ford F-350 Super Duty Pickup cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2003 Ford F-350 Super Duty Pickup 7.3 V8 DIESEL
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 26 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford F-350 Super Duty Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Ford F-350 Super Duty Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Ford F-350 Super Duty Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2003 Ford F-350 Super Duty Pickup 7.3 V8 DIESEL
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford F-350 Super Duty Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Ford F-350 Super Duty Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Ford F-350 Super Duty Pickup cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2003 Ford F-350 Super Duty Pickup 6.0 V8 DIESEL
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 26 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford F-350 Super Duty Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2003 Ford F-350 Super Duty Pickup vehicle. |
Access the Complete guide! |