Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2004 Oldsmobile Silhouette car and truck
repair procedures including Oldsmobile engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2004 Oldsmobile Silhouette automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2004 Oldsmobile Silhouette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Oldsmobile Silhouette cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Aztek, Rendezvous & Vue -> Canyon, Colorado, Sierra & Silverado -> Equinox & Torrent -> Express & Savana -> HHR -> Installation -> Montana, Silhouette, Trans Sport & Venture -> Removal -> Tracker
Vehicle: 2004 Oldsmobile Silhouette 3.4 V6 GAS
Aztek, Rendezvous & Vue
Removal
- Raise and support vehicle.
- Mark relationship of drum to hub.
- Remove and discard retaining clip.
- Remove brake drum. If brake drum does not come off easily, proceed as follows:
- Loosen parking brake cable.
- Remove backing plate access hole plug.
- Disengage self adjuster by inserting suitable flat-bladed tool through backing plate access hole.
- Loosen adjuster screw by inserting another flat-bladed tool through access hole .
- Install access hole plug.
- Apply small amount of penetrating oil around brake drum center hole.
- Remove brake drum.
- Disengage adjuster spring hook e...
CLICK HERE TO GET FULL ACCESS TO 2004 Oldsmobile Silhouette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Oldsmobile Silhouette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Oldsmobile Silhouette cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 2004 Oldsmobile Silhouette 3.4 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2004 Oldsmobile Silhouette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Oldsmobile Silhouette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Oldsmobile Silhouette cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Caliper Service -> Assemble -> Disassemble -> Front -> Inspection -> Installation -> Rear -> Removal
Vehicle: 2004 Oldsmobile Silhouette 3.4 V6 GAS
Removal
Front
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed back into its bore.
- Raise and support vehicle, then remove wheels.
- Push piston back into its bore using suitable C-clamp, Fig. .
- Remove brake caliper hose bolt, then two metal gaskets from brake caliper bolt.
- Remove two caliper mounting bolts and lift caliper off of rotor.
Rear
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed ...
CLICK HERE TO GET FULL ACCESS TO 2004 Oldsmobile Silhouette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Oldsmobile Silhouette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Oldsmobile Silhouette cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Bendix Master Cylinder -> Delco Master Cylinder -> Disassemble -> Tracker Master Cylinder -> Wheel Cylinder
Vehicle: 2004 Oldsmobile Silhouette 3.4 V6 GAS
Delco Master Cylinder
When performing the following procedures, refer to Figs. and , noting that the composite reservoir may vary in design.
Disassemble
- Remove master cylinder from vehicle.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm. Replace if cut, cracked or deformed.
- Remove fluid level switch and proportioning valve assembly, if equipped.
- Depress primary piston and remove lock ring.
- Plug primary fluid outlet (outlet nearest to cowl when master cylinder is installed), then apply compressed air into secondary fluid outlet ...
CLICK HERE TO GET FULL ACCESS TO 2004 Oldsmobile Silhouette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Oldsmobile Silhouette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Oldsmobile Silhouette cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Description
Vehicle: 2004 Oldsmobile Silhouette 3.4 V6 GAS
The caliper assembly slides on its mounting surfaces, Fig. . Upon brake application, hydraulic pressure against the piston forces the inboard pad against the inboard...
CLICK HERE TO GET FULL ACCESS TO 2004 Oldsmobile Silhouette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Oldsmobile Silhouette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Oldsmobile Silhouette cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 2004 Oldsmobile Silhouette 3.4 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2004 Oldsmobile Silhouette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2004 Oldsmobile Silhouette vehicle.
|
| Access the Complete guide! |
