Auto Parts Search
We have info for following modifications of 2006 Jeep Commander
- 2006 Jeep Commander 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2006 Jeep Commander 3.7 V6 GAS, CID:226, Fuel Injection, Aspiration:226, Engine VIN:, Desg:K
- 2006 Jeep Commander Limited 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2006 Jeep Commander Limited 5.7 V8 GAS, CID:345, Fuel Injection, Aspiration:345, Engine VIN:, Desg:2
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Electronic Throttle Control Indicator ->
Vehicle: 2006 Jeep Commander 4.7 V8 GAS
When the ignition is turned On, the lamp will light for approximately 6-12 seconds as a bulb inspection. If the lamp is illuminated with the engine running, the vehicle is usually drivable but the electronic throttle system must be diagnosed and servic...
CLICK HERE TO GET FULL ACCESS TO 2006 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Check Engine Lamp -> Chrysler, Dodge, Jeep & Plymouth Except Ram 50
Vehicle: 2006 Jeep Commander 4.7 V8 GAS
On models less OBD II, the Check Engine lamp should light for approximately 3 seconds after the ignition has been turned On as a bulb inspection. If improper or no signals are received by the Powertrain Control Module (PCM) from various sensors and monitored systems or if the PCM enters its Limp-In mode, the PCM will light the Check Engine lamp. On Chrysler, Dodge and Plymouth models, After diagnosing and servicing the vehicle, the PCM memory will be cleared after approximately 40 to 100 ignition key On-Off cycles or by using a suitable scan tool. ...
CLICK HERE TO GET FULL ACCESS TO 2006 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Check Engine Lamp -> Chrysler, Dodge, Jeep & Plymouth Except Ram 50
Vehicle: 2006 Jeep Commander Limited 4.7 V8 GAS
On models less OBD II, the Check Engine lamp should light for approximately 3 seconds after the ignition has been turned On as a bulb inspection. If improper or no signals are received by the Powertrain Control Module (PCM) from various sensors and monitored systems or if the PCM enters its Limp-In mode, the PCM will light the Check Engine lamp. On Chrysler, Dodge and Plymouth models, After diagnosing and servicing the vehicle, the PCM memory will be cleared after approximately 40 to 100 ignition key On-Off cycles or by using a suitable scan tool. ...
CLICK HERE TO GET FULL ACCESS TO 2006 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Service 4WD System Warning Lamp ->
Vehicle: 2006 Jeep Commander Limited 5.7 V8 GAS
This lamp should light for a approximately 2 seconds when the ignition is turned On as a bulb check. If the warning lamp...
CLICK HERE TO GET FULL ACCESS TO 2006 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2006-09 Commander -> Relearn -> Reset
Vehicle: 2006 Jeep Commander 4.7 V8 GAS
Reset
The Low Tire Pressure indicator lamp will flash slowly and sound a single tone when tire pressure is low. If tire pressure drops lower, the indicator lamp will flash rapidly and the tone will be continuous. When the tire is inflated to the proper pressure the lamp and tone will turn Off. The vehicle may need to be driven at a speed above 15 MPH for up to 10 minutes for the TPMS to receive this information. If the lamp remains On, a problem in the low tire warning system is present and the low tire warning system must be ...
CLICK HERE TO GET FULL ACCESS TO 2006 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Check Gauge Warning Lamp ->
Vehicle: 2006 Jeep Commander Limited 5.7 V8 GAS
When the ignition is turned On, the lamp will light for approximately 2 seconds as a bulb inspection. The PCM continually monitors the engine oil pressure, engine coolant temperature and electrical system voltage. The check gauges lamp w...
CLICK HERE TO GET FULL ACCESS TO 2006 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 Jeep Commander vehicle. |
Access the Complete guide! |