Auto Parts Search
We have info for following modifications of 2007 Audi A6 Quattro
- 2007 Audi A6 Quattro 3.2 V6 GAS, CC:3123, Fuel Injection
- 2007 Audi A6 Quattro 4.2 V8 GAS, CC:4163, Fuel Injection
- 2007 Audi A6 Quattro Avant 3.2 V6 GAS, CC:3123, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi A6 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi A6 Quattro cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Audi A6 Quattro Avant 3.2 V6 GAS
- Raise and support vehicle.
- Remove rear section of exhaust system at clamp(s).
- Pry off rear attachments of drive shaft heat shield.
- Remove securing bolts for center bearing When removing securing bolts, support drive shaft by hand. Do not bend drive shaft.
- Remove heat shield. Continue supporting drive shaft.
- Screw in securing bolts for center bearing again hand-tight.
- Remove drive shaft heat shield from transmission.
- Check for a factory marking (colored dot) on drive shaft and on drive shaft flange on final drive at rear. If no colored dot is present, mark position of drive shaft fl...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi A6 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi A6 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi A6 Quattro cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Audi A6 Quattro 3.2 V6 GAS
- Raise and support vehicle.
- Remove rear section of exhaust system at clamp(s).
- Pry off rear attachments of drive shaft heat shield.
- Remove securing bolts for center bearing When removing securing bolts, support drive shaft by hand. Do not bend drive shaft.
- Remove heat shield. Continue supporting drive shaft.
- Screw in securing bolts for center bearing again hand-tight.
- Remove drive shaft heat shield from transmission.
- Check for a factory marking (colored dot) on drive shaft and on drive shaft flange on final drive at rear. If no colored dot is present, mark position of drive shaft fl...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi A6 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi A6 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi A6 Quattro cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Audi A6 Quattro 3.2 V6 GAS
Front
- On models with air spring suspension, position vehicle on lifting platform.
- On models without air spring suspension, raise and support vehicle.
- On all models, remove wheel.
- Loosen collar bolt for outer joint of drive axle.
- Remove noise insulation.
- Remove drive axle from transmission flange shaft.
- Remove drive axle. If there is not sufficient room to remove drive axle, proceed as follows:
- Remove nut and hex bolt and pull out both upper links upward.
- Swing wheel bearing housing out to side.
- Remove drive axle.
- Reverse procedure to install, noting the following:
- Torque wheel lug nu...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi A6 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi A6 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi A6 Quattro cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Audi A6 Quattro Avant 3.2 V6 GAS
Front
- On models with air spring suspension, position vehicle on lifting platform.
- On models without air spring suspension, raise and support vehicle.
- On all models, remove wheel.
- Loosen collar bolt for outer joint of drive axle.
- Remove noise insulation.
- Remove drive axle from transmission flange shaft.
- Remove drive axle. If there is not sufficient room to remove drive axle, proceed as follows:
- Remove nut and hex bolt and pull out both upper links upward.
- Swing wheel bearing housing out to side.
- Remove drive axle.
- Reverse procedure to install, noting the following:
- Torque wheel lug nu...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi A6 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi A6 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi A6 Quattro cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Audi A6 Quattro 4.2 V8 GAS
Front
- On models with air spring suspension, position vehicle on lifting platform.
- On models without air spring suspension, raise and support vehicle.
- On all models, remove wheel.
- Loosen collar bolt for outer joint of drive axle.
- Remove noise insulation.
- Remove drive axle from transmission flange shaft.
- Remove drive axle. If there is not sufficient room to remove drive axle, proceed as follows:
- Remove nut and hex bolt and pull out both upper links upward.
- Swing wheel bearing housing out to side.
- Remove drive axle.
- Reverse procedure to install, noting the following:
- Torque wheel lug nu...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi A6 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi A6 Quattro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi A6 Quattro cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Audi A6 Quattro 4.2 V8 GAS
- Raise and support vehicle.
- Remove rear section of exhaust system at clamp(s).
- Pry off rear attachments of drive shaft heat shield.
- Remove securing bolts for center bearing When removing securing bolts, support drive shaft by hand. Do not bend drive shaft.
- Remove heat shield. Continue supporting drive shaft.
- Screw in securing bolts for center bearing again hand-tight.
- Remove drive shaft heat shield from transmission.
- Check for a factory marking (colored dot) on drive shaft and on drive shaft flange on final drive at rear. If no colored dot is present, mark position of drive shaft fl...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi A6 Quattro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Audi A6 Quattro vehicle. |
Access the Complete guide! |