Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Audi S4 car and truck
repair procedures including Audi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2007 Audi S4 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2007 Audi S4
- 2007 Audi S4 4.2 V8 GAS, CC:4172, Fuel Injection
- 2007 Audi S4 Avant 4.2 V8 GAS, CC:4172, Fuel Injection
- 2007 Audi S4 Cabriolet 4.2 V8 GAS, CC:4172, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi S4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi S4 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Audi S4 Cabriolet 4.2 V8 GAS
Front
- Remove wheel trim. Pull trim cap off light-alloy wheels, using puller in vehicle tool kit.
- Loosen bolt for drive axle outer joint by a maximum of 90°. Vehicle must be standing on its wheels to avoid risk of accident.
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Screw all 5 wheel bolts hand-tight.
- Remove hex bolt for drive axle outer joint.
- Unbolt drive axle from flange shaft on transmission. If not enough space is available for removing drive axle, proceed as follows:
- Remove nut and hex bolt and pull out both upper links upward.
- Swing wheel bearing housing out ...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi S4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi S4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi S4 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Audi S4 Avant 4.2 V8 GAS
- Raise and support vehicle.
- Remove rear section of exhaust system at clamp(s).
- Pry off rear attachments of drive shaft heat shield.
- Remove securing bolts for center bearing When removing securing bolts, support drive shaft by hand. Do not bend drive shaft.
- Remove heat shield. Continue supporting drive shaft.
- Screw in securing bolts for center bearing again hand-tight.
- Remove drive shaft heat shield from transmission.
- Check for a factory marking (colored dot) on drive shaft and on drive shaft flange on final drive at rear. If no colored dot is present, mark position of drive shaft fl...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi S4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi S4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi S4 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Audi S4 4.2 V8 GAS
- Raise and support vehicle.
- Remove rear section of exhaust system at clamp(s).
- Pry off rear attachments of drive shaft heat shield.
- Remove securing bolts for center bearing When removing securing bolts, support drive shaft by hand. Do not bend drive shaft.
- Remove heat shield. Continue supporting drive shaft.
- Screw in securing bolts for center bearing again hand-tight.
- Remove drive shaft heat shield from transmission.
- Check for a factory marking (colored dot) on drive shaft and on drive shaft flange on final drive at rear. If no colored dot is present, mark position of drive shaft fl...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi S4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi S4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi S4 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Audi S4 Avant 4.2 V8 GAS
Front
- Remove wheel trim. Pull trim cap off light-alloy wheels, using puller in vehicle tool kit.
- Loosen bolt for drive axle outer joint by a maximum of 90°. Vehicle must be standing on its wheels to avoid risk of accident.
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Screw all 5 wheel bolts hand-tight.
- Remove hex bolt for drive axle outer joint.
- Unbolt drive axle from flange shaft on transmission. If not enough space is available for removing drive axle, proceed as follows:
- Remove nut and hex bolt and pull out both upper links upward.
- Swing wheel bearing housing out ...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi S4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi S4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi S4 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Audi S4 4.2 V8 GAS
Front
- Remove wheel trim. Pull trim cap off light-alloy wheels, using puller in vehicle tool kit.
- Loosen bolt for drive axle outer joint by a maximum of 90°. Vehicle must be standing on its wheels to avoid risk of accident.
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Screw all 5 wheel bolts hand-tight.
- Remove hex bolt for drive axle outer joint.
- Unbolt drive axle from flange shaft on transmission. If not enough space is available for removing drive axle, proceed as follows:
- Remove nut and hex bolt and pull out both upper links upward.
- Swing wheel bearing housing out ...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi S4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Audi S4 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Audi S4 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Audi S4 Cabriolet 4.2 V8 GAS
- Raise and support vehicle.
- Remove rear section of exhaust system at clamp(s).
- Pry off rear attachments of drive shaft heat shield.
- Remove securing bolts for center bearing When removing securing bolts, support drive shaft by hand. Do not bend drive shaft.
- Remove heat shield. Continue supporting drive shaft.
- Screw in securing bolts for center bearing again hand-tight.
- Remove drive shaft heat shield from transmission.
- Check for a factory marking (colored dot) on drive shaft and on drive shaft flange on final drive at rear. If no colored dot is present, mark position of drive shaft fl...
CLICK HERE TO GET FULL ACCESS TO 2007 Audi S4 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2007 Audi S4 vehicle.
|
| Access the Complete guide! |
