Auto Parts Search
We have info for following modifications of 2008 Cadillac CTS
- 2008 Cadillac CTS 3.6 V6 GAS, CID:217, Fuel Injection, Aspiration:217, Engine VIN:, Desg:7
- 2008 Cadillac CTS 3.6 V6 GAS, CID:217, Fuel Injection, Aspiration:217, Engine VIN:, Desg:V
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac CTS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac CTS cars and light trucks from 1990+.
Power Brake Units -> Precautions
Vehicle: 2008 Cadillac CTS 3.6 V6 GAS
- After disassembling power brake unit, soak metal components in solvent.
- Use only alcohol on components containing rubber. After components have been thoroughly cleaned and rinsed in solvent, they should be washed again in clean alcohol before assembly.
- Use compressed air to blow dirt and cleaning fluid...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac CTS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac CTS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac CTS cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Rear Disc Brake -> Disc Brake Specifications -> Caliper Specifications
Vehicle: 2008 Cadillac CTS 3.6 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac CTS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac CTS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac CTS cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Dual Piston Front Disc Brake -> Caliper Service -> Assemble -> Bushing & Boot Replacement -> Disassemble -> Inspection -> Installation -> Mounting Bracket Service -> Removal
Vehicle: 2008 Cadillac CTS 3.6 V6 GAS
Removal
- Drain master cylinder fluid level to 1/3 full.
- Raise and support vehicle, then remove front tire and wheel assemblies.
- Mark wheel to hub and bearing relationship for installation alignment.
- Push pistons back together into caliper bores using suitable C-clamp and block of wood.
- Remove mounting bolt, copper washer and inlet fitting. Plug opening in inlet fitting. Do not crimp brake hose.
- Remove two mounting bolts and caliper.
Disassemble
- Position shop towel in interior component of caliper, then slowly apply compressed air to inlet port and remove pistons. One piston must be parti...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac CTS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac CTS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac CTS cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Rear Disc Brake -> Disc Brake Specifications -> Caliper Specifications
Vehicle: 2008 Cadillac CTS 3.6 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac CTS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac CTS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac CTS cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting -> Master Cylinder Internal Fluid Leakage Check -> Road Test
Vehicle: 2008 Cadillac CTS 3.6 V6 GAS
When troubleshooting the hydraulic brake system, perform the following inspections.
Master Cylinder Internal Fluid Leakage Check
Start engine and depress the brake pedal. If the pedal gradually falls under constant pressure, the hydraulic system may be leaking. Raise the vehicle on a lift and inspect all tubing lines and backing plates for signs of leakage. It may be required to lift or remove the carpeting or floor mats to inspect for boost...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac CTS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac CTS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac CTS cars and light trucks from 1990+.
Anti-Lock Brakes -> TRW 440 -> System Service -> Bleed Sequence -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> CTS -> CTS, DTS, Lucerne & STS -> DTS & Lucerne -> DTS, Impala, Lucerne & STS -> Electronic Brake Control Module (EBCM) -> Front -> Impala -> Rear -> STS -> Wheel Speed Sensor
Vehicle: 2008 Cadillac CTS 3.6 V6 GAS
Brake System Bleed
The Auto Bleed Procedure may be terminated at any time during the process by pressing the EXIT button. No further Scan Tool prompts pertaining to the Auto Bleed procedure will be given. After exiting the bleed procedure, relieve bleed pressure and disconnect bleed equipment per manufacturers instructions. Failure to properly relieve pressure may result in spilled brake fluid.
- Raise and support vehicle, then remove all four tire and wheel assemblies.
- Inspect brake system for leaks and visual damage.
- Lower vehicle and inspect battery charge.
- Connect a suitably program...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac CTS BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Cadillac CTS vehicle. |
Access the Complete guide! |