Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Cadillac XLR car and truck
repair procedures including Cadillac engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Cadillac XLR automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Cadillac XLR
- 2008 Cadillac XLR 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:A
- 2008 Cadillac XLR V 4.4 V8 GAS, CC:4371, CID:267, Fuel Injection, Aspiration:267, Engine VIN:, Desg:D
- 2008 Cadillac XLR Platinum 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:A
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac XLR AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac XLR cars and light trucks from 1990+.
Anti-Lock Brakes -> Delco/Bosch Type 7.2 -> System Service -> Aura & Malibu -> Auto Bleed -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> Corvette -> Electronic Brake Control Module (EBCM) -> Hydraulic System Flush -> Lateral Accelerator -> Manual Bleed -> Pressure Bleed -> STS -> Wheel Speed Sensor -> XLR -> Yaw Rate Sensor -> Yaw Rate Sensor/Lateral Accelerometer
Vehicle: 2008 Cadillac XLR 4.6 V8 GAS
Brake System Bleed
Auto Bleed
Perform manual or pressure bleeding as outlined in "Manual Bleed" or "Pressure Bleed" before auto bleeding system.
- Turn ignition switch to Off position.
- Raise and support vehicle, then remove tire and wheel assemblies.
- Inspect brake system for leaks and damage.
- Connect a suitably programmed scan tool to Data Link Connector (DLC), DLC is located in lefthand side of instrument panel below steering column.
- Turn ignition switch to On position. Do not start engine.
- Establish scan tool communications by selecting ABS/TCS, Special Functions and Automate Bleed Procedure...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac XLR BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac XLR AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac XLR cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Rotor Replace -> Corvette -> Installation -> Removal -> XLR
Vehicle: 2008 Cadillac XLR Platinum 4.6 V8 GAS
Corvette
Removal
- Remove 2/3 of total brake fluid capacity from master cylinder reservoir.
- Raise and support vehicle, then remove tire and wheel assembly.
- Remove caliper guide pin bolts, then the caliper from rotor and caliper mounting bracket. Suspend caliper from upper control arm.
- Remove mounting bolts and mounting bracket.
- Remove rotor from hub assembly.
Installation
- Ensure guiding surfaces on shoe and lining assemblies and mounting bracket are seated properly, then position caliper over rotor and onto mounting bracket.
- Press caliper housing downward to compress bias springs, then insta...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac XLR BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac XLR AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac XLR cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Tightening Specifications
Vehicle: 2008 Cadillac XLR 4.6 V8 GAS
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac XLR BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac XLR AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac XLR cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting -> Master Cylinder Internal Fluid Leakage Check -> Road Test
Vehicle: 2008 Cadillac XLR 4.6 V8 GAS
When troubleshooting the hydraulic brake system, perform the following inspections.
Master Cylinder Internal Fluid Leakage Check
Start engine and depress the brake pedal. If the pedal gradually falls under constant pressure, the hydraulic system may be leaking. Raise the vehicle on a lift and inspect all tubing lines and backing plates for signs of leakage. It may be required to lift or remove the carpeting or floor mats to inspect for boost...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac XLR BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac XLR AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac XLR cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Precautions
Vehicle: 2008 Cadillac XLR 4.6 V8 GAS
- Keep grease and other foreign material off brake linings, caliper, surfaces of disc and external surfaces of hub.
- Avoid deforming disc, and nicking or scratching brake linings.
- Worn or damaged rubber piston seals should be replaced.
- During removal and installation of a wheel assembly, ensure not to interfere with or damage caliper splash shield, or bleeder screw.
- Front wheel bearing...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac XLR BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Cadillac XLR AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Cadillac XLR cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Caliper Service -> Assemble -> Corvette -> Disassemble -> Inspection -> Installation -> Removal -> XLR
Vehicle: 2008 Cadillac XLR 4.6 V8 GAS
Removal
Corvette
- Remove 2/3 of total brake fluid capacity from master cylinder reservoir.
- Raise and support vehicle, then remove tire and wheel assembly.
- If caliper requires overhaul, remove inlet fitting mounting bolt, then disconnect inlet fitting from caliper housing.
- Discard both gaskets, then plug openings in inlet fitting and caliper. Do not crimp brake hose since this may damage hose's internal structure.
- Remove caliper guide pin bolts, then the caliper from rotor and caliper mounting bracket. If only shoe and linings require replacement, suspend caliper from upper control arm ...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac XLR BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
