Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Toyota Tacoma car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Toyota Tacoma automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Toyota Tacoma
- 2008 Toyota Tacoma 2.7 L4 GAS, CC:2694, Fuel Injection
- 2008 Toyota Tacoma 4.0 V6 GAS, CC:3956, Fuel Injection
- 2008 Toyota Tacoma X-RUNNER 4.0 V6 GAS, CC:3956, Fuel Injection
- 2008 Toyota Tacoma PRE Runner 2.7 L4 GAS, CC:2694, Fuel Injection
- 2008 Toyota Tacoma PRE Runner 4.0 V6 GAS, CC:3956, Fuel Injection
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Toyota Tacoma AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Toyota Tacoma cars and light trucks sold in the U.S. from 1990+.
Toyota -> Air Bag Warning Lamp -> 2003-09 Tacoma
Vehicle: 2008 Toyota Tacoma PRE Runner 2.7 L4 GAS
- Connect two service wires to terminals Tc and CG of data link connector.
- Turn ignition switch to On position and wait for approximately 6 seconds.
- SRS warning lamps will illuminate 2-4 seconds later. Within 1-5 seconds, ground terminal Tc of DLC.
- SRS warning lamp will go off within 2-4 seconds. Within 1-5 seconds, release...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Tacoma MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Toyota Tacoma AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Toyota Tacoma cars and light trucks sold in the U.S. from 1990+.
Toyota -> Engine Oil Reminder/Maintenance Required Lamp -> 2005-09 Tacoma
Vehicle: 2008 Toyota Tacoma PRE Runner 2.7 L4 GAS
- Turn the ignition switch to the On position and ensure that the LCD display screen is in the odometer mode.
- Turn ignition switch to the Off position.
- While pressing the TRIP button, turn the ignition switch On. Hold the button down through the entire reset procedure.
- Continue to push the TRIP switch...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Tacoma MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Toyota Tacoma AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Toyota Tacoma cars and light trucks sold in the U.S. from 1990+.
Toyota -> Malfunction Indicator Lamp (MIL) ->
Vehicle: 2008 Toyota Tacoma X-RUNNER 4.0 V6 GAS
On some models equipped with OBD II, the MIL will also illuminate if the fuel tank filler cap is not properly tightened. Tighten fuel tank filler cap until it clicks.
The MIL should light when the ignition switch is placed in the On position without starting the engine. When the engine is started, the lamp should go out. If it remains lit, a fault has been detected by the diagnostic system and has logged a diagnostic trouble code. If the fault does not occur again within three trips, the lamp will go out but a diagnostic tro...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Tacoma MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Toyota Tacoma AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Toyota Tacoma cars and light trucks sold in the U.S. from 1990+.
Toyota -> Tire Pressure Warning Lamp -> 2007-09 Tacoma -> Registration -> Relearn -> Reset -> System Initialization -> Tire Pressure Sensor & Transmitter -> TPMS ECU
Vehicle: 2008 Toyota Tacoma 2.7 L4 GAS
Reset
This warning lamp will illuminate when tire pressure falls below a specified psi. When the warning lamp illuminates, check the air pressure of the tire and adjust it to specified pressure. When the vehicle is driven more than 18 mph after the adjustment, the lamp will go off.
Relearn
Registration
TPMS ECU
If replacing the TPMS ECU, prior to removal, use a suitably programmed scan tool to read the registered transmitter identification number for all wheels and note them for registration.
- Connect a suitably programmed scan tool to DLC3 located under the LH side of the instrument pa...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Tacoma MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Toyota Tacoma AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Toyota Tacoma cars and light trucks sold in the U.S. from 1990+.
Toyota -> Engine Oil Reminder/Maintenance Required Lamp -> 2005-09 Tacoma
Vehicle: 2008 Toyota Tacoma 2.7 L4 GAS
- Turn the ignition switch to the On position and ensure that the LCD display screen is in the odometer mode.
- Turn ignition switch to the Off position.
- While pressing the TRIP button, turn the ignition switch On. Hold the button down through the entire reset procedure.
- Continue to push the TRIP switch...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Tacoma MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Toyota Tacoma AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Toyota Tacoma cars and light trucks sold in the U.S. from 1990+.
Toyota -> Anti-Lock Brake System (ABS)/Vehicle Stability Control (VSC) System Warning Lamp -> 2002-09 Tacoma
Vehicle: 2008 Toyota Tacoma X-RUNNER 4.0 V6 GAS
The anti-lock warning lamp is used to warn of a system fault. The lamp will be lit during engine start-up, but should go out when the self-diagnostic system verifies proper anti-lock operation. If the lamp remains lit, a fault in the anti-lock brake system is indicated. After system diagnosis and repair are complete, the lamp can be reset using the following procedures:
- Place ignition switch ...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Tacoma MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Toyota Tacoma vehicle.
|
| Access the Complete guide! |
