Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Toyota FJ Cruiser car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2009 Toyota FJ Cruiser automobile. Try the Automotix DIY solution today!
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Toyota FJ Cruiser AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Toyota FJ Cruiser cars and light trucks sold in the U.S. from 1990+.
Toyota -> Low Oil Level Warning Indicator ->
Vehicle: 2009 Toyota FJ Cruiser 4.0 V6 GAS
This lamp lights to indicate that the engine oil level is below a specified level. The lamp will be illuminated during engine start-up. If...
CLICK HERE TO GET FULL ACCESS TO 2009 Toyota FJ Cruiser MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Toyota FJ Cruiser AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Toyota FJ Cruiser cars and light trucks sold in the U.S. from 1990+.
Toyota -> Air Bag Warning Lamp -> 2007-09 FJ Cruiser
Vehicle: 2009 Toyota FJ Cruiser 4.0 V6 GAS
- Connect two service wires to terminals Tc and CG of data link connector.
- Disconnect Tc within 10 seconds after DTC output begins.
- SRS warning lamps will illuminate 3 seconds later. Within 2-4 seconds, connect terminals Tc and CG of DLC.
- SRS warning lamp will go off within 2-4 seconds. Within 2-4 seconds, disconnect te...
CLICK HERE TO GET FULL ACCESS TO 2009 Toyota FJ Cruiser MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Toyota FJ Cruiser AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Toyota FJ Cruiser cars and light trucks sold in the U.S. from 1990+.
Toyota -> Tire Pressure Warning Lamp -> 2008-09 FJ Cruiser -> Registration -> Relearn -> Reset -> System Initialization -> Tire Pressure Sensor & Transmitter -> TPMS ECU
Vehicle: 2009 Toyota FJ Cruiser 4.0 V6 GAS
Reset
This warning lamp will illuminate when tire pressure falls below a specified psi. When the warning lamp illuminates, check the air pressure of the tire and adjust it to specified pressure. When the vehicle is driven more than 18 mph after the adjustment, the lamp will go off.
Relearn
Registration
TPMS ECU
If replacing the TPMS ECU, prior to removal, use a suitably programmed scan tool to read the registered transmitter identification number for all wheels and note them for registration.
- Connect a suitably programmed scan tool to DLC3 located under the LH side of the instrumen...
CLICK HERE TO GET FULL ACCESS TO 2009 Toyota FJ Cruiser MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Toyota FJ Cruiser AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Toyota FJ Cruiser cars and light trucks sold in the U.S. from 1990+.
Toyota -> Automatic Transmission Oil Temperature Warning Lamp ->
Vehicle: 2009 Toyota FJ Cruiser 4.0 V6 GAS
This lamp will be illuminated when automatic transmission or transfer case fluid temperature exceeds 302°F. If the lamp lights, allow vehicle to operate at idle speed until fluid temperature falls below 248°F; t...
CLICK HERE TO GET FULL ACCESS TO 2009 Toyota FJ Cruiser MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Toyota FJ Cruiser AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Toyota FJ Cruiser cars and light trucks sold in the U.S. from 1990+.
Toyota -> Malfunction Indicator Lamp (MIL) ->
Vehicle: 2009 Toyota FJ Cruiser 4.0 V6 GAS
On some models equipped with OBD II, the MIL will also illuminate if the fuel tank filler cap is not properly tightened. Tighten fuel tank filler cap until it clicks.
The MIL should light when the ignition switch is placed in the On position without starting the engine. When the engine is started, the lamp should go out. If it remains lit, a fault has been detected by the diagnostic system and has logged a diagnostic trouble code. If the fault does not occur again within three trips, the lamp will go out but a diagnostic tro...
CLICK HERE TO GET FULL ACCESS TO 2009 Toyota FJ Cruiser MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Toyota FJ Cruiser AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Toyota FJ Cruiser cars and light trucks sold in the U.S. from 1990+.
Toyota -> Engine Oil Reminder/Maintenance Required Lamp -> 2007-09 FJ Cruiser
Vehicle: 2009 Toyota FJ Cruiser 4.0 V6 GAS
To reset Oil Replacement Reminder light, turn ignition On and ensure that the odometer is displayed on the LCD (reset procedure will not work in the TRIP mode) Turn ignition to Off position while pressing the TRIP switch button, turn ignition On. Hold button down through entire reset procedure. The o...
CLICK HERE TO GET FULL ACCESS TO 2009 Toyota FJ Cruiser MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 Toyota FJ Cruiser vehicle.
|
| Access the Complete guide! |
