Auto Parts Search
Infiniti CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Infiniti REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Model
| EX35 | FX35 | FX45 | FX50 |
| G20 | G35 | G37 | I30 |
| I35 | J30 | M30 | M35 |
| M45 | Q45 | QX4 | QX56 |
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Infiniti car and truck
repair procedures including Infiniti engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system
specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your Infiniti
automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR Infiniti AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported Infiniti cars and light trucks from 1990+
Import Compressor Service -> Calsonic Compressor -> COMPRESSOR CLUTCH SERVICE -> CLUTCH ASSEMBLY, REPLACE -> Installation -> Removal -> V5 COMPRESSOR -> V6 COMPRESSOR
Vehicle: 1995 Infiniti J30 3.0 V6 GAS
CLUTCH ASSEMBLY, REPLACE
V5 COMPRESSOR
Removal
- Using spanner wrench No KV99845991 or equivalent, hold clutch hub and remove retaining nut, Fig. .
- Install jig Nos. KV99859981, KV99845982 and bolt No. KV99845992 as shown in Fig. .
- Tighten upper jig while holding lower jig.
- Remove snap ring from shaft.
- Remove pulley using suitable gear puller.
- Remove lead wire fixing screw, then remove coil using suitable gear puller.
Installation
- Install clutch jig Nos. KV99859981 and KV99845982 an...
CLICK HERE TO GET FULL ACCESS TO Infiniti A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR Infiniti AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Infiniti cars and light trucks from 1990+.
Infiniti -> Disc Brakes -> Brake Pad Service -> Front -> FX35, FX45, G35, M45, Q45 & QX56 -> I35 -> Rear
Vehicle: 2004 Infiniti FX35 3.5 V6 GAS
Front
- Raise and support vehicle, then remove master cylinder cap.
- Disconnect wheel speed sensor connector.
- Remove lower caliper mounting pin/bolt.
- Pivot caliper upward to remove caliper and retainers from torque member, Figs. through .
- Remove inner and outer pads and shims.
- Compress caliper piston using suitable C-clamp.
- Reverse procedure to install, noting the following:
- Apply Poly Butyl Cuprysil (PBC) to surface between shim pad and shim.
- Ensure inner and outer pad return lever, Fig. , is secured on upper side of pad retainer.
Rear
I35
- Raise and support vehicle.
- Remove master...
CLICK HERE TO GET FULL ACCESS TO Infiniti BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR Infiniti AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Infiniti cars and light trucks sold in the U.S. for 1980+.
Infiniti -> Fuel Filter Replacement -> All Models -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 1995 Infiniti G20 2.0 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveabilty symptoms may occur. The vehicle may need to be driven 10...
CLICK HERE TO GET FULL ACCESS TO Infiniti FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Infiniti AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Infiniti cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1990 Infiniti Q45 4.5 V8 GAS
- Raise and support vehicle, then remove rear wheels.
- Remove wheel bearing locknut.
- Remove side flange mounting bolts from final drive side, then separate shaft.
- On wheel si...
CLICK HERE TO GET FULL ACCESS TO Infiniti DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Infiniti AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Infiniti cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2005 Infiniti FX45 4.5 V8 GAS
The TPMS (Tire Pressure Monitor System) is controlled by the Body Control Module (BCM). The BCM receives its tire pressure signal from the remote keyless entry receiver. The remote keyless entry receiver receives...
CLICK HERE TO GET FULL ACCESS TO Infiniti TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Infiniti AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Infiniti cars and light trucks from 1990+.
Alternator, Replace
Vehicle: 1997 Infiniti QX4 3.3 V6 GAS
- Disconnect battery ground cable.
- Remove battery.
- Remove air intake duct.
- Remove upper radiator hose.
- Remove fan drive.
- Remove upper and lower drive belts.
- Remove alternator and stay mounting bolts.
- Remove battery ground cable mounting bolt.
- Remove alternator bracket mounting bolts.
- Disconnect alter...
CLICK HERE TO GET FULL ACCESS TO Infiniti STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR Infiniti AUTOMOBILES
Cabin air filter locations and replacement procedures with corresponding images for most domestic and imported Infiniti cars and light trucks sold in the U.S. as equipped to the current model year.
Cabin Air Filter Service -> Infiniti -> 2005-08 G35
Vehicle: 2007 Infiniti G35 3.5 V6 GAS
Under normal operating conditions the cabin air filter should be replaced every 12 months or 15,000 miles. In dusty areas change the cabin air filter more often.
- Remove the glove compartment retaining screws, Fig. .
- Carefully pull back on the glove compartment to release the pawls, then remove the glove compar...
CLICK HERE TO GET FULL ACCESS TO Infiniti CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Infiniti AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Infiniti cars and light trucks sold in the U.S. from 1990+.
Infiniti -> Vehicle Dynamic Control (VDC) Warning Lamp ->
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
The VDC lamp should illuminate when the ignition switch is placed in the on position for a few seconds or when the VDC control switch is in the off position. If the VDC lamps illuminates while ope...
CLICK HERE TO GET FULL ACCESS TO Infiniti MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Infiniti AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Infiniti cars and light trucks from 1990+
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 1999 Infiniti I30 3.0 V6 GAS
Inlet
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at heater core.
- Remove hose from heater core.
- Reposition hose clamp at heater pipe.
- Remove hose from heater pipe.
- Remove hose from vehicle.
- Reverse procedure to install.
Outlet
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp...
CLICK HERE TO GET FULL ACCESS TO Infiniti RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Infiniti AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Infiniti cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2008 Infiniti FX35 3.5 V6 GAS
- Rotate or lift the belt tensioner arm, using a suitable tool to relieve tension from dr...
CLICK HERE TO GET FULL ACCESS TO Infiniti SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Infiniti AUTOMOBILES
Component location diagrams for most Infiniti cars and light trucks sold in the U.S. from 1990+.
 Auto Light System Diagram for 2004 Infiniti G35 3.5 V6 GASComponents on diagram: |
 Door Harness Connector Locations. Rear LH Door Diagram for 1995 Infiniti Q45 4.5 V8 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Infiniti PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Infiniti AUTOMOBILES
OEM drawn wiring diagrams for most Infiniti cars and light trucks sold in the U.S.
 2005 Infiniti FX35 3.5 V6 GAS Wiring DiagramComponents on diagram: |
 2008 Infiniti EX35 3.5 V6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Infiniti WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Infiniti AUTOMOBILES
OEM TSB listings for most Infiniti cars and light trucks sold in the U.S. from 1985+.
|
Document: LOW TIRE PRESSURE WARNING SYSTEM (LTPWS) - TECHNICAL INFORMATION Vehicle: 2000 Infiniti G20 2.0 L4 GAS Auto Systems: |
|
Document: Electronic Control Unit Damage Can Result From Improper Battery Connection Vehicle: 2009 Infiniti FX50 5.0 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Infiniti TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Infiniti AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Infiniti cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Infiniti cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Infiniti cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Infiniti cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Infiniti SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
