Auto Parts Search
1990 Ford Bronco II CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
HYDRAULIC BRAKE SYSTEMS, FORD -> BLEEDING BRAKES
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
Bleed primary and secondary hydraulic brake systems separately, bleeding the longest line first on each system. Do not allow reservoir to run dry during bleeding operation. Never reuse fluid that has been drained from the hydraulic system.
- Loosen master cylinder to hydraulic line nuts and wrap shop cloths around tubing below fitting to absorb escaping brake fluid.
- Depress brake pedal slowly forcing air trapped in master cylinder out at fitting.
- Hold pedal down and tighten fittings, then release brake pedal. Releasing brake pedal before fittings are tightened will allow air to ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
Ford Motor Co. Light Trucks, SUVs & Vans -> Fuel Shutoff Switch Location -> 1985-90 Bronco II, F250HD & F350, F-Super Duty, Bronco & F150-350
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
The inertia swit...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Tighten transfer case flange bolts in a cross pattern.
- Torque front propeller shaft flange bolts to transfer case to 75 ft. lbs. if equipped.
- T...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
Starter, Replace
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
- Disconnect battery ground cable.
- Raise and support vehicle, if required.
- Disconnect electrical connector or solenoid relay wire from starter motor.
- Remove starter motor attachi...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
Ford Motor Co. Trucks -> Fuel Reset ->
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
The FUEL RESET indicator is grounded through the inertia switch whenever vehicle is in a high force situation. The Inertia F...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
Radiator, Replace
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
- Disconnect negative battery cable at battery.
- Drain cooling system into a suitable container.
- Remove overflow tube from coolant recovery bottle and detach it from radiator shroud.
- Remove four shroud attaching bolts and position it over fan.
- Remove lower radiator hose and position aside.
- Remove upper radiator hose and p...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1990 Ford Bronco II AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1990 Ford Bronco II 2.9 V6 GAS
- Loosen adjustment and pivot bolts.
- On models equipped with automatic tensioners,lift tensioner by rotating it counterclockwise.
- On all models, remove old belts.
- Install new belts, ensure proper belt groove contact.
- On models less automatic tensioners, adjust belt tension as follows:
- Install a suitable belt tension gauge tool, at ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1990 Ford Bronco II AUTOMOBILES
Component location diagrams for most 1990 Ford Bronco II cars and light trucks sold in the U.S. from 1990+.
Brake Pedal Components Diagram for 1990 Ford Bronco II 2.9 V6 GAS Components on diagram: |
RH Side Of Engine Diagram for 1990 Ford Bronco II 2.9 V6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1990 Ford Bronco II AUTOMOBILES
OEM drawn wiring diagrams for most 1990 Ford Bronco II cars and light trucks sold in the U.S.
1990 Ford Bronco II 2.9 V6 GAS Wiring Diagram Components on diagram: |
1990 Ford Bronco II 2.9 V6 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1990 Ford Bronco II AUTOMOBILES
OEM TSB listings for most 1990 Ford Bronco II cars and light trucks sold in the U.S. from 1985+.
Document: WHINING / BUZZING NOISE COMES THROUGH ENTERTAINMENT OR TWO-WAY RADIO SPEAKER Vehicle: 1990 Ford Bronco II 2.9 V6 GAS Symptoms: |
Document: FORD MOTOR COMPANY POSITION ON PROPYLENE GLYCOL-BASED ENGINE COOLANTS Vehicle: 1990 Ford Bronco II 2.9 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1990 Ford Bronco II AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1990 Ford Bronco II cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1990 Ford Bronco II cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1990 Ford Bronco II cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1990 Ford Bronco II cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Bronco II SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1990 Ford Bronco II vehicle. |
Access the Complete guide! |