Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Jaguar XJ6 car and truck
repair procedures including Jaguar engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Jaguar XJ6 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1990 Jaguar XJ6
- 1990 Jaguar XJ6 4.0 L6 GAS, CC:3980, Fuel Injection, Engine VIN:, Desg:7
- 1990 Jaguar XJ6 Executive 4.0 L6 GAS, CC:3980, Fuel Injection, Engine VIN:, Desg:9
- 1990 Jaguar XJ6 Sovereign 4.0 L6 GAS, CC:3980, Fuel Injection, Engine VIN:, Desg:7
BRAKE SERVICE PROCEDURES FOR 1990 Jaguar XJ6 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Jaguar XJ6 cars and light trucks from 1990+.
JAGUAR, DISC BRAKES -> FRONT CALIPER REPLACEMENT -> XJ6 -> XJS
Vehicle: 1990 Jaguar XJ6 Executive 4.0 L6 GAS
XJS
- Raise and support vehicle.
- Remove brake pads, then disconnect and plug brake line.
- Remove lock wire (2) and remove two bolts and spring washers (3), Fig. , securing caliper and stub axle carrier.
- Note number of shims between steering arm and brake caliper. Remove caliper.
- Reverse procedure to install, noting the following:
- Ensure correct number of shims are installed between calipe...
CLICK HERE TO GET FULL ACCESS TO 1990 Jaguar XJ6 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Jaguar XJ6 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Jaguar XJ6 cars and light trucks from 1990+.
JAGUAR, HYDRAULIC BRAKE SYSTEMS -> MASTER CYLINDER -> OVERHAUL -> REPLACE
Vehicle: 1990 Jaguar XJ6 Sovereign 4.0 L6 GAS
REPLACE
- Remove cover from brake fluid reservoir cap and disconnect wires from brake fluid level indicator.
- Remove reservoir cap and filter.
- With a syringe, drain fluid from master cylinder.
- Disconnect and plug brake lines from master cylinder.
- Operate brake pedal approximately ten times to ensure there is no vacuum remaining in servo.
- Remove master cylinder from power booster.
- Reverse procedure to install, noting the following:
- Torque master cylinder to servo bolts to 16-20 ft. lbs.
- Bleed hydraulic brake system.
OVERHAUL
- Remove master cylinder from vehicle.
- Carefully pry out master cylinder...
CLICK HERE TO GET FULL ACCESS TO 1990 Jaguar XJ6 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Jaguar XJ6 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Jaguar XJ6 cars and light trucks from 1990+.
JAGUAR -> SYSTEM SERVICE -> ACCUMULATOR, REPLACE -> ACTUATION UNIT, REPLACE -> ELECTRONIC CONTROL UNIT (ECU), REPLACE -> Front -> MOTOR & PUMP UNIT, REPLACE -> Rear -> WHEEL SPEED SENSOR, REPLACE
Vehicle: 1990 Jaguar XJ6 Executive 4.0 L6 GAS
ACCUMULATOR, REPLACE
- Discharge hydraulic accumulator by depressing brake pedal until it becomes difficult to operate (approximately 20 times).
- Place a shop rag or towel around accumulator area to absorb any spilled fluid.
- Remove accumulator, then discard O-ring.
- Reverse procedure to install, noting the following:
- Install New O-ring on accumulator, then install and torque accumulator to 29.5-34 ft. lbs.
- Turn ignition switch to On position, then wait until accumulator is charged to upper cut-out point and ABS warning light goes out.
ACTUATION UNIT, REPLACE
- Discharge hydraulic accumulator b...
CLICK HERE TO GET FULL ACCESS TO 1990 Jaguar XJ6 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Jaguar XJ6 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Jaguar XJ6 cars and light trucks from 1990+.
JAGUAR, DISC BRAKES -> REAR CALIPER REPLACEMENT -> XJ6 -> XJS
Vehicle: 1990 Jaguar XJ6 Executive 4.0 L6 GAS
XJS
- Raise and support rear of vehicle.
- Remove nuts and bolts securing tie-plate to rear suspension unit. Remove tie-plate.
- Ensure parking brake lever is in fully OFF position. Lift carpet adjacent to handbrake lever mounting for access to cable adjusting nuts. Fig. .
- Loosen cable lock/adjusting nuts.
- Release springs from parking brake caliper arms (1) Fig. .
- Move right hand arm to center of vehicle, enabling end of inner cable (2), to be detached from operating arm.
- Slide rubber cover from outer cable (3) and release outer cable from other parking brake operating arm.
- Position...
CLICK HERE TO GET FULL ACCESS TO 1990 Jaguar XJ6 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Jaguar XJ6 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Jaguar XJ6 cars and light trucks from 1990+.
JAGUAR, DISC BRAKES -> BRAKE BLEEDING
Vehicle: 1990 Jaguar XJ6 Sovereign 4.0 L6 GAS
Maintain brake fluid at correct level in reservoir during brake bleeding procedure.
- Raise and support vehicle.
- Clean reservoir and filler cap to ensure fluid is clean and no dirt enters reservoir.
- Hold brake fluid level warning light cable and remove filler cap/float assembly. Top fluid level to base of filler neck.
- Start the bleeding process at right rear wheel.
- Rem...
CLICK HERE TO GET FULL ACCESS TO 1990 Jaguar XJ6 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Jaguar XJ6 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Jaguar XJ6 cars and light trucks from 1990+.
JAGUAR, POWER BRAKE UNITS -> REPLACEMENT
Vehicle: 1990 Jaguar XJ6 Sovereign 4.0 L6 GAS
- Remove engine compartment stabilizer bar located above brake booster.
- Pry vacuum elbow from booster, then remove master cylinder/booster securing nuts.
- Loosen throttle cable/bracket locknut and disconnect kickdown switch feed wires.
- Disconnect throttle cable from turntable, then remove fluid reservoir securing bolts.
- Remove reservoir from mounting bracket and reposition away from area.
- Remove pedal housing nuts/bolts.
- Ease master cylinder away from booster moun...
CLICK HERE TO GET FULL ACCESS TO 1990 Jaguar XJ6 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
