Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Suzuki Swift car and truck
repair procedures including Suzuki engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Suzuki Swift automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1990 Suzuki Swift
- 1990 Suzuki Swift 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1990 Suzuki Swift GT 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1990 Suzuki Swift GA 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1990 Suzuki Swift GL 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1990 Suzuki Swift L 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1990 Suzuki Swift S 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
BRAKE SERVICE PROCEDURES FOR 1990 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Suzuki Swift cars and light trucks from 1990+.
SUZUKI, ANTI-LOCK BRAKES -> COMPONENT TESTING -> 4WD SWITCH -> PRESSURE LIMIT (ISOLATION/DUMP) VALVE -> RWAL RELAY -> RWAL SYSTEM ELECTRIC CIRCUIT CHECK -> STOP LIGHT SWITCH -> WHEEL SPEED SENSOR
Vehicle: 1990 Suzuki Swift 1.3 L4 GAS
RWAL SYSTEM ELECTRIC CIRCUIT CHECK
The electrical circuit of RWAL system can be checked by measuring voltage of ECM connector terminals. RWAL ECM cannot be check by itself. If is strictly prohibited to connect voltmeter or ohmmeter to RWAL ECM with harness connector disconnected from it.
Battery must be fully charged to perform this test as terminal voltage will be directly affected by battery voltage.
- Remove RWAL ECM from body.
- Connect RWAL ECM harness coupler to RWAL ECM.
- Check voltage at each terminal of coupler connected. Refer to Fig. for voltage specifications.
WHEEL SPEED SEN...
CLICK HERE TO GET FULL ACCESS TO 1990 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Suzuki Swift cars and light trucks from 1990+.
SUZUKI, DRUM BRAKES -> SWIFT -> BRAKE DRUM, REPLACE -> BRAKE SHOE, REPLACE -> WHEEL CYLINDER, REPLACE
Vehicle: 1990 Suzuki Swift GA 1.3 L4 GAS
BRAKE DRUM, REPLACE
- Raise and support vehicle, remove spindle cap.
- On sedan models, remove drum screws.
- On all models, unstake and remove spindle nut and washer, then release parking brake lever.
- Remove parking brake lever cover, then loosen parking brake cable locking nut.
- To increase clearance between shoe and drum, proceed as follows:
- Remove backing plate plug.
- Insert screwdriver into plug hole till its tip contacts shoe hold down spring, then push hold down spring as shown in Fig. .
- Using slide hammer and drum remover No. 09943-17911 or equivalent, pull off brake drum.
- Reverse procedure to ins...
CLICK HERE TO GET FULL ACCESS TO 1990 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Suzuki Swift cars and light trucks from 1990+.
SUZUKI, DRUM BRAKES -> SERVICE BRAKE ADJUSTMENT
Vehicle: 1990 Suzuki Swift GL 1.3 L4 GAS
These brakes are self-adjusting, but do require adjustment for proper drum to shoe clearance when brake shoe has been replaced o...
CLICK HERE TO GET FULL ACCESS TO 1990 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Suzuki Swift cars and light trucks from 1990+.
SUZUKI, HYDRAULIC BRAKES -> MASTER CYLINDER OVERHAUL
Vehicle: 1990 Suzuki Swift GA 1.3 L4 GAS
- Remove master cylinder as outlined under "Master Cylinder, Replace."
- Remove circlip, then the primary piston.
- Remove piston stoppe...
CLICK HERE TO GET FULL ACCESS TO 1990 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Suzuki Swift cars and light trucks from 1990+.
SUZUKI, HYDRAULIC BRAKES -> BRAKE PEDAL HEIGHT ADJUSTMENT
Vehicle: 1990 Suzuki Swift GL 1.3 L4 GAS
The brake pedal should normally be at same height as clutch pedal. Check that distance between brake booster mounting surface (with gasket) and pushrod clevis pin hole should be ...
CLICK HERE TO GET FULL ACCESS TO 1990 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Suzuki Swift cars and light trucks from 1990+.
SUZUKI, ANTI-LOCK BRAKES -> COMPONENT TESTING -> 4WD SWITCH -> PRESSURE LIMIT (ISOLATION/DUMP) VALVE -> RWAL RELAY -> RWAL SYSTEM ELECTRIC CIRCUIT CHECK -> STOP LIGHT SWITCH -> WHEEL SPEED SENSOR
Vehicle: 1990 Suzuki Swift GT 1.3 L4 GAS
RWAL SYSTEM ELECTRIC CIRCUIT CHECK
The electrical circuit of RWAL system can be checked by measuring voltage of ECM connector terminals. RWAL ECM cannot be check by itself. If is strictly prohibited to connect voltmeter or ohmmeter to RWAL ECM with harness connector disconnected from it.
Battery must be fully charged to perform this test as terminal voltage will be directly affected by battery voltage.
- Remove RWAL ECM from body.
- Connect RWAL ECM harness coupler to RWAL ECM.
- Check voltage at each terminal of coupler connected. Refer to Fig. for voltage specifications.
WHEEL SPEED SEN...
CLICK HERE TO GET FULL ACCESS TO 1990 Suzuki Swift BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
