Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Toyota Celica car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1990 Toyota Celica automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1990 Toyota Celica
- 1990 Toyota Celica GT 2.2 L4 GAS, CC:2164, Fuel Injection, Engine VIN:, Desg:S
- 1990 Toyota Celica ST 1.6 L4 GAS, CC:1587, Fuel Injection, Engine VIN:, Desg:A
- 1990 Toyota Celica GTS Sport 2.2 L4 GAS, CC:2164, Fuel Injection, Engine VIN:, Desg:S
- 1990 Toyota Celica ALL Trac 2.0 L4 GAS, CC:1998, Fuel Injection, Engine VIN:, Desg:S
- 1990 Toyota Celica GTS 2.2 L4 GAS, CC:2164, Fuel Injection, Engine VIN:, Desg:S
BRAKE SERVICE PROCEDURES FOR 1990 Toyota Celica AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Toyota Celica cars and light trucks from 1990+.
TOYOTA, DRUM BRAKES -> SERVICE -> Inspection -> Installation -> Removal -> TYPE 1 (2WD DUO SERVO TYPE) -> TYPE 2 (2WD LEADING-TRAILING TYPE) -> TYPE 3 -> TYPE 4 -> TYPE 5 -> TYPE 6 -> TYPE 7
Vehicle: 1990 Toyota Celica GT 2.2 L4 GAS
TYPE 1 (2WD DUO SERVO TYPE)
Removal
- Raise and support rear of vehicle them remove wheel and tire assembly.
- Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
- Remove two shoe return springs, using suitable tool, Fig.
- Push lever upward, then remove cable, shoe guide, plate and cable guide.
- Remove spring from lever, then the lever and spring.
- Remove two tension springs, using a suitable tool, then shoe hold-down springs and pins.
- Remove shoes, adjuster and...
CLICK HERE TO GET FULL ACCESS TO 1990 Toyota Celica BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Toyota Celica AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Toyota Celica cars and light trucks from 1990+.
TOYOTA, ANTI-LOCK BRAKES -> DESCRIPTION
Vehicle: 1990 Toyota Celica GTS 2.2 L4 GAS
By use of a micro-computer, this anti-lock brake system controls brake fluid pressure to prevent wheel lock. With this sys...
CLICK HERE TO GET FULL ACCESS TO 1990 Toyota Celica BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Toyota Celica AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Toyota Celica cars and light trucks from 1990+.
TOYOTA, HYDRAULIC BRAKES -> MASTER CYLINDER -> Assembly -> Disassembly -> Except Van -> Inspection -> OVERHAUL -> REPLACE -> Van
Vehicle: 1990 Toyota Celica GT 2.2 L4 GAS
REPLACE
Except Van
- On MR2, remove luggage compartment trim cover by removing two clips after disengaging inner part of clip.
- On all models, label, disconnect brake lines using line wrench 09751-36011, or equivalent. Then cap brake lines from master cylinder.
- Disconnect wire connector from brake pressure switch and then disconnect level warning switch connector, if equipped.
- Remove master cylinder to brake unit attaching nuts, then remove master cylinder, wire clamp, gasket and 3-way union, as needed.
- Reverse procedure to install. Bleed brake system.
Van
- Disconnect battery ground cable
- Re...
CLICK HERE TO GET FULL ACCESS TO 1990 Toyota Celica BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Toyota Celica AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Toyota Celica cars and light trucks from 1990+.
TOYOTA, POWER BRAKE UNITS -> TROUBLESHOOTING
Vehicle: 1990 Toyota Celica GTS Sport 2.2 L4 GAS
Refer to "Hydraulic Brakes" for...
CLICK HERE TO GET FULL ACCESS TO 1990 Toyota Celica BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Toyota Celica AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Toyota Celica cars and light trucks from 1990+.
TOYOTA, ANTI-LOCK BRAKES -> COMPONENT REPLACEMENT -> ABS COMPUTER -> BRAKE ACTUATOR -> Celica 4WD -> Except Celica 4WD
Vehicle: 1990 Toyota Celica ALL Trac 2.0 L4 GAS
BRAKE ACTUATOR
Except Celica 4WD
- Remove brake fluid from actuator using a suitable tool.
- On Pickup and 4Runner models, remove battery.
- On all models, disconnect connectors from actuator.
- Remove brake tubes from actuator using suitable wrench.
- On Pickup and 4Runner models, turn steering wheel clockwise until it locks, then disconnect power steering lines from actuator.
- On all models, remove actuator bracket attaching bolt, then remove actuator and bracket assembly.
- Remove actuator mounting nuts and actuator.
- Reverse procedure to install, noting the fo...
CLICK HERE TO GET FULL ACCESS TO 1990 Toyota Celica BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Toyota Celica AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1990 Toyota Celica cars and light trucks from 1990+.
TOYOTA, HYDRAULIC BRAKES -> WHEEL CYLINDERS -> OVERHAUL -> REPLACE
Vehicle: 1990 Toyota Celica GTS Sport 2.2 L4 GAS
REPLACE
- Remove brake shoes as described under "Drum Brakes."
- Disconnect brake line using line wrench 09751-36011, or equivalent. Then remove two wheel cylinder attaching bolts and wheel cylinder.
- Reverse procedure to install. Torque wheel cylinder bolts to 7 ft. lbs. Bleed brakes.
OVERHAUL
Refer to Fig.for disassembled view of a typical wheel cylinder.
- Remove boots, pis...
CLICK HERE TO GET FULL ACCESS TO 1990 Toyota Celica BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
