Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1991 BMW M3 car and truck
repair procedures including BMW engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1991 BMW M3 automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1991 BMW M3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 BMW M3 cars and light trucks from 1990+.
Anti-Lock Brakes -> DIAGNOSIS & TESTING
Vehicle: 1991 BMW M3 2.3 L4 GAS
The electronic control unit monitors the Anti-Lock Brake System (ABS) constantly. The system must be checked when the ABS indicator lamp does not go out, comes on while driving or does not come on when ignition is turned on. A BMW service tester is required to check any malfunction of the syst...
CLICK HERE TO GET FULL ACCESS TO 1991 BMW M3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 BMW M3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 BMW M3 cars and light trucks from 1990+.
Hydraulic Brakes -> COMPONENT REPLACEMENT -> 735, 750 & 850 -> MASTER CYLINDER, REPLACE -> POWER FLOW REGULATOR, REPLACE
Vehicle: 1991 BMW M3 2.3 L4 GAS
MASTER CYLINDER, REPLACE
- Remove brake fluid from master cylinder with a syringe.
- Remove plug and clutch hose if equipped.
- Remove fluid reservoir.
- Remove brake lines, then mounting bolts.
- Remove master cylinder.
- Reverse procedure to install and bleed brake system.
POWER FLOW REGULATOR, REPLACE
735, 750 & 850
- With engine off, discharge hydraulic reservoir by operating brake...
CLICK HERE TO GET FULL ACCESS TO 1991 BMW M3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 BMW M3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 BMW M3 cars and light trucks from 1990+.
Anti-Lock Brakes -> COMPONENT REPLACEMENT -> CONTROL UNIT, REPLACE -> FRONT SPEED SENSOR, REPLACE -> HYDRAULIC UNIT, REPLACE -> REAR SPEED SENSOR, REPLACE
Vehicle: 1991 BMW M3 2.3 L4 GAS
HYDRAULIC UNIT, REPLACE
- Disconnect battery ground cable.
- Remove coolant expansion tank.
- Remove brake lines from hydraulic unit as follows: front left; front right; rear left; rear right.
- Remove brake hydraulic lines from master cylinder to hydraulic unit.
- Remove cover from top of hydraulic cover, then loosen, but do not remove, bolts for hydraulic unit.
- Remove retaining screws and pull of f multiple pin connector and disconnect ground wire.
- Pull up on the front of the hydraulic unit, then disconnect the rear and remove the unit.
- Reverse procedure to install, ensuring hydraulic lin...
CLICK HERE TO GET FULL ACCESS TO 1991 BMW M3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 BMW M3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 BMW M3 cars and light trucks from 1990+.
Power Brake Units -> POWER BRAKE UNIT SERVICE -> 318, 325, 525 & 535 -> 735, 750 & 850 -> POWER BRAKE BOOSTER, REPLACE
Vehicle: 1991 BMW M3 2.3 L4 GAS
POWER BRAKE BOOSTER, REPLACE
318, 325, 525 & 535
- Remove master cylinder from booster.
- Remove lower left trim panel.
- Disconnect bayonet pin and clip from booster pushrod, below instrument panel. Fig.
- Detach booster from pedal base. Remove booster from engine compartment.
- Reverse procedure to install.
735, 750 & 850
- With engine off, discharge hydraulic reservoir by operating brake pedal approximately 20 times with same force required for fu...
CLICK HERE TO GET FULL ACCESS TO 1991 BMW M3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 BMW M3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 BMW M3 cars and light trucks from 1990+.
Hydraulic Brakes -> DESCRIPTION -> 735 & 750 -> 850 -> H-31 HYDRAULIC SYSTEM -> MASTER CYLINDER
Vehicle: 1991 BMW M3 2.3 L4 GAS
H-31 HYDRAULIC SYSTEM
The H-31 hydraulic system, Fig. incorporates a power flow regulator which diverts a small flow of fluid from the power steering operating circuit for the power assisted brake system. It charges the hydraulic reservoir in a high pressure range without impairing the function of power steering. The pressurized hydraulic oil volume is supplied to the booster for the sake of power assistance and is applied by operating the connected standard tandem master cylinder. should the power steering pump fail, the hydraulic reservoir has sufficient reserve pressure to permit...
CLICK HERE TO GET FULL ACCESS TO 1991 BMW M3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 BMW M3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 BMW M3 cars and light trucks from 1990+.
Disc Brakes -> TIGHTENING SPECIFICATIONS
Vehicle: 1991 BMW M3 2.3 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1991 BMW M3 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
