Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1992 BMW 318I car and truck
repair procedures including BMW engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1992 BMW 318I automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1992 BMW 318I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 BMW 318I cars and light trucks from 1990+.
Hydraulic Brakes -> DESCRIPTION -> 735 & 750 -> 850 -> H-31 HYDRAULIC SYSTEM -> MASTER CYLINDER
Vehicle: 1992 BMW 318I 1.8 L4 GAS
H-31 HYDRAULIC SYSTEM
The H-31 hydraulic system, Fig. incorporates a power flow regulator which diverts a small flow of fluid from the power steering operating circuit for the power assisted brake system. It charges the hydraulic reservoir in a high pressure range without impairing the function of power steering. The pressurized hydraulic oil volume is supplied to the booster for the sake of power assistance and is applied by operating the connected standard tandem master cylinder. should the power steering pump fail, the hydraulic reservoir has sufficient reserve pressure to permit...
CLICK HERE TO GET FULL ACCESS TO 1992 BMW 318I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 BMW 318I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 BMW 318I cars and light trucks from 1990+.
Anti-Lock Brakes -> DIAGNOSIS & TESTING
Vehicle: 1992 BMW 318I 1.8 L4 GAS
The electronic control unit monitors the Anti-Lock Brake System (ABS) constantly. The system must be checked when the ABS indicator lamp does not go out, comes on while driving or does not come on when ignition is turned on. A BMW service tester is required to check any malfunction of the syst...
CLICK HERE TO GET FULL ACCESS TO 1992 BMW 318I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 BMW 318I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 BMW 318I cars and light trucks from 1990+.
Disc Brakes -> PARKING BRAKE ADJUSTMENT
Vehicle: 1992 BMW 318I 1.8 L4 GAS
- Ensure parking brake lever is fully released and cables operate freely, then raise and support rear of vehicle.
- On models with wheel bolts, remove 1 wheel bolt from each wheel. On models with studs, remove rear wheels and secure brake discs using lug nuts and spacers.
- On all models, rotate wheel until bolt hole is aligned with parking brake star adjuster. Adjuster is located approximately 30 ° behind the vertical axis of the wheel on 300 series vehicles, Fig. , or 45 ° below horizontal axis of wheel toward rear of vehicle on 500, 600, 700 & 800 series vehic...
CLICK HERE TO GET FULL ACCESS TO 1992 BMW 318I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 BMW 318I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 BMW 318I cars and light trucks from 1990+.
Hydraulic Brakes -> BRAKE SYSTEM BLEEDING
Vehicle: 1992 BMW 318I 1.8 L4 GAS
The following procedure has been revised by BMW Technical Service Bulletin No. 34 06 90 (3134).
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to right rear wheel. Bleed until no bubbles appear.
- Repeat step 2 for left rear, right front and left front wheels.
- Support rear suspension at wheel carriers and lower car so rear suspension compresses to its normal loaded position (to prevent damage to output shaft jo...
CLICK HERE TO GET FULL ACCESS TO 1992 BMW 318I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 BMW 318I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 BMW 318I cars and light trucks from 1990+.
Anti-Lock Brakes -> COMPONENT REPLACEMENT -> CONTROL UNIT, REPLACE -> FRONT SPEED SENSOR, REPLACE -> HYDRAULIC UNIT, REPLACE -> REAR SPEED SENSOR, REPLACE
Vehicle: 1992 BMW 318I 1.8 L4 GAS
HYDRAULIC UNIT, REPLACE
- Disconnect battery ground cable.
- Remove coolant expansion tank.
- Remove brake lines from hydraulic unit as follows: front left; front right; rear left; rear right.
- Remove brake hydraulic lines from master cylinder to hydraulic unit.
- Remove cover from top of hydraulic cover, then loosen, but do not remove, bolts for hydraulic unit.
- Remove retaining screws and pull of f multiple pin connector and disconnect ground wire.
- Pull up on the front of the hydraulic unit, then disconnect the rear and remove the unit.
- Reverse procedure to install, ensuring hydraulic lin...
CLICK HERE TO GET FULL ACCESS TO 1992 BMW 318I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 BMW 318I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 BMW 318I cars and light trucks from 1990+.
Disc Brakes -> FRONT DISC BRAKE PADS REPLACEMENT -> 318 & 325 -> EXCEPT 318 & 325
Vehicle: 1992 BMW 318I 1.8 L4 GAS
318 & 325
- Raise and support vehicle, then remove front wheels.
- Remove brake pad wear indicator connector from left side of caliper.
- Remove anti-rattle clip, then the caliper sliding bolt plastic caps.
- Lift brake hose out of holder, then remove caliper sliding bolts.
- Remove caliper toward rear. Remove brake pads, then suspend caliper from frame with wire.
- Reverse procedure to install, noting the following:
- Compress caliper piston into bore.
- Check fluid ...
CLICK HERE TO GET FULL ACCESS TO 1992 BMW 318I BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
