Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1992 Toyota Paseo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Toyota Paseo cars and light trucks from 1990+.
TOYOTA, POWER BRAKE UNITS -> TROUBLESHOOTING
Vehicle: 1992 Toyota Paseo 1.5 L4 GAS
Refer to "Hydraulic Brakes" for...
CLICK HERE TO GET FULL ACCESS TO 1992 Toyota Paseo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Toyota Paseo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Toyota Paseo cars and light trucks from 1990+.
TOYOTA, POWER BRAKE UNITS -> BRAKE BOOSTER REPLACEMENT -> Cressida -> Except Cressida -> INSTALLATION -> REMOVAL
Vehicle: 1992 Toyota Paseo 1.5 L4 GAS
REMOVAL
Except Cressida
- On models with airbag, disable airbag system as described under "Airbag System Disarming."
- On models less airbag, disconnect battery ground cable.
- On all models, remove master cylinder as outlined under "Master Cylinder, Replace" in the "Hydraulic Brake System" section.
- On 1992 Camry and Celica models, push away charcoal vapor canister for better access.
- On Supra, remove cruise actuator.
- On Supra and 1992 Celica models, remove lower finish panel or lower pad as outlined in "Dash Panel Service."
- Remove pedal return spring, clip, clevis pin and clevis locknut, Fi...
CLICK HERE TO GET FULL ACCESS TO 1992 Toyota Paseo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Toyota Paseo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Toyota Paseo cars and light trucks from 1990+.
TOYOTA, POWER BRAKE UNITS -> BRAKE BOOSTER OVERHAUL
Vehicle: 1992 Toyota Paseo 1.5 L4 GAS
The brake booster on these models ca...
CLICK HERE TO GET FULL ACCESS TO 1992 Toyota Paseo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Toyota Paseo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Toyota Paseo cars and light trucks from 1990+.
TOYOTA, DRUM BRAKES -> SERVICE -> Inspection -> Installation -> Removal -> TYPE 1 (2WD DUO SERVO TYPE) -> TYPE 2 (2WD LEADING-TRAILING TYPE) -> TYPE 3 -> TYPE 4 -> TYPE 5 -> TYPE 6 -> TYPE 7
Vehicle: 1992 Toyota Paseo 1.5 L4 GAS
TYPE 1 (2WD DUO SERVO TYPE)
Removal
- Raise and support rear of vehicle them remove wheel and tire assembly.
- Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
- Remove two shoe return springs, using suitable tool, Fig.
- Push lever upward, then remove cable, shoe guide, plate and cable guide.
- Remove spring from lever, then the lever and spring.
- Remove two tension springs, using a suitable tool, then shoe hold-down springs and pins.
- Remove shoes, adjuster and...
CLICK HERE TO GET FULL ACCESS TO 1992 Toyota Paseo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Toyota Paseo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Toyota Paseo cars and light trucks from 1990+.
TOYOTA, HYDRAULIC BRAKES -> MASTER CYLINDER -> Assembly -> Disassembly -> Except Van -> Inspection -> OVERHAUL -> REPLACE -> Van
Vehicle: 1992 Toyota Paseo 1.5 L4 GAS
REPLACE
Except Van
- On MR2, remove luggage compartment trim cover by removing two clips after disengaging inner part of clip.
- On all models, label, disconnect brake lines using line wrench 09751-36011, or equivalent. Then cap brake lines from master cylinder.
- Disconnect wire connector from brake pressure switch and then disconnect level warning switch connector, if equipped.
- Remove master cylinder to brake unit attaching nuts, then remove master cylinder, wire clamp, gasket and 3-way union, as needed.
- Reverse procedure to install. Bleed brake system.
Van
- Disconnect battery ground cable
- Re...
CLICK HERE TO GET FULL ACCESS TO 1992 Toyota Paseo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Toyota Paseo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Toyota Paseo cars and light trucks from 1990+.
TOYOTA, HYDRAULIC BRAKES -> WHEEL CYLINDERS -> OVERHAUL -> REPLACE
Vehicle: 1992 Toyota Paseo 1.5 L4 GAS
REPLACE
- Remove brake shoes as described under "Drum Brakes."
- Disconnect brake line using line wrench 09751-36011, or equivalent. Then remove two wheel cylinder attaching bolts and wheel cylinder.
- Reverse procedure to install. Torque wheel cylinder bolts to 7 ft. lbs. Bleed brakes.
OVERHAUL
Refer to Fig.for disassembled view of a typical wheel cylinder.
- Remove boots, pis...
CLICK HERE TO GET FULL ACCESS TO 1992 Toyota Paseo BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1992 Toyota Paseo vehicle. |
Access the Complete guide! |