Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 BMW 525I car and truck
repair procedures including BMW engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1993 BMW 525I automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1993 BMW 525I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 525I cars and light trucks from 1990+.
Power Brake Units -> Diagnosis & Testing -> 318, 325, 525 & 535 -> Brake Booster Vacuum Supply Check -> Function Test
Vehicle: 1993 BMW 525I 2.5 L6 GAS
Function Test
- Operate brake pedal ten times with engine stopped.
- If brake pedal gives, system is okay.
- If brake pedal does not give, check valve, vacuum hose and/or rubber ring between master cylinder and brake booster could be defective.
Brake Booster Vacuum Supply Check
318, 325...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 525I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 525I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 525I cars and light trucks from 1990+.
Disc Brakes -> Adjustments -> Parking Brake
Vehicle: 1993 BMW 525I 2.5 L6 GAS
Parking Brake
- Ensure parking brake lever is fully released and cables operate freely, then raise and support rear of vehicle.
- On models with wheel bolts, remove 1 wheel bolt from each wheel. On models with studs, remove rear wheels and secure brake discs using lug nuts and spacers.
- On all models, rotate wheel until bolt hole is aligned with parking brake star adjuster. Adjuster is located approximately 30° behind the vertical axis of the wheel on 318 and 325 models, Fig. , or 45° below horizontal axis of wheel toward rear of vehicle on all models except 318 and 325, Fig. ...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 525I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 525I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 525I cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> 318 and 325 -> 525, 535, 735 & 750 -> Diagnostic Tests
Vehicle: 1993 BMW 525I 2.5 L6 GAS
The electronic control unit monitors the Anti-Lock Brake System (ABS) constantly. The system must be checked when the ABS indicator lamp does not go out, comes on while driving or does not come on when ignition is turned on. A BMW service tester ...
[[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 1993 BMW 525I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 525I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 525I cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting
Vehicle: 1993 BMW 525I 2.5 L6 GAS
Refer to Fig. , for hy...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 525I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 525I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 525I cars and light trucks from 1990+.
Anti-lock Brakes -> Description
Vehicle: 1993 BMW 525I 2.5 L6 GAS
The Anti-Lock Brake System (ABS) consists of a control unit, hydraulic unit, speed sensors and wiring harness. Each speed sensor has a gear wheel which runs past the permanently magnetized edge of the speed sensor installed in the wheel hub. The rotary motion of the wheels is recorded by inductive sensors and an electric signal is sent to the electronic control unit.
The electronic control unit is located in a compartment on the right side of the engine compartment. This control unit inputs acceleration, deceleration and slip factors from the electronic speed sensors, which are propo...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 525I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 525I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 525I cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> 318 & 325 -> Except 318 & 325 -> Front Brake Pads, Replace -> Rear Brake Pads, replace
Vehicle: 1993 BMW 525I 2.5 L6 GAS
Front Brake Pads, Replace
318 & 325
- Raise and support vehicle, then remove front wheels.
- Remove brake pad wear indicator connector from left side of caliper.
- Remove anti-rattle clip, then the caliper sliding bolt plastic caps.
- Lift brake hose out of holder, then remove caliper sliding bolts.
- Remove caliper toward rear. Remove brake pads, then suspend caliper from frame with wire.
- Reverse procedure to install, noting the following:
- Compress caliper piston into bore.
- Check fluid level and bleed brake system as necessary.
- Tighten to specifications.
Except 318 & 325
- Remove wheels and disconne...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 525I BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1993 BMW 525I vehicle.
|
| Access the Complete guide! |
