Auto Parts Search
1993 Chevrolet Beretta CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chevrolet REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
General Service Domestic Vehicles -> 1992-93 -> Discharging System
Vehicle: 1993 Chevrolet Beretta GTZ 2.3 L4 GAS
R-134a systems require the use of special service equipment designed specifically for R-134a systems. R-12 servicing equipment cannot be used on R-134a systems.
Refrigerant-12 recovery stations cannot be used on Refrigerant-134a systems. A separate recovery station must be used on R-134a systems. The refrigerants are not compatible and will contaminate the R-12 recovery station.
The use of refrigerant recovery and recycling stations allows the recovery and reuse of refrigerant after contaminants and moisture have been removed.
When using a recovery or recycli...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
Disc Brakes -> AC-Delco Single Piston Front Disc Brake (Type 2) -> Caliper Service -> CALIPER ASSEMBLE -> CALIPER DISASSEMBLE -> CALIPER INSTALLATION -> CALIPER REMOVAL
Vehicle: 1993 Chevrolet Beretta GT 2.2 L4 GAS
CALIPER REMOVAL
- Remove approximately 2/3 of brake fluid from master cylinder.
- Raise and support front of vehicle, then remove wheel and tire assembly.
- Position suitable pliers over inboard pad and housing as shown in Fig. , and squeeze pliers to compress caliper piston.
- If caliper assembly is being removed for service, remove inlet fitting attaching bolt, copper washer, and inlet fitting from caliper housing. Plug opening in inlet fitting to prevent fluid loss and contamination. Do not crimp brake hose, as this may damage internal structure of hose. If only shoe and lining assemblie...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
General Motors Corp./Saturn Passenger Cars -> Fuel Filter Scheduled Maintenance -> 1980-06 Gasoline Engine Models Except Catera, LeMans (1988-93) Metro, Nova (1985-88), Saturn & Sprint -> Normal Service -> Severe Service
Vehicle: 1993 Chevrolet Beretta GT 3.1 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1993 Chevrolet Beretta GTZ 3.1 V6 GAS
- Disconnect negative battery cable.
- Raise and support vehicle and remove wheel and tire assembly.
- Install drive axle seal protector J-34754 or equivalent on outer joint.
- Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning and remove hub nut and washer.
- Remove lower ball joint cotter pin and nut, then loosen joint using a suitable pry bar or tool No. J-29330. If right axle is being removed, turn wheel to left, if left axle is being removed, turn wheel to right.
- Insert a prybar between suspension support...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
Starter, Replace
Vehicle: 1993 Chevrolet Beretta 2.2 L4 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Disconnect solenoid wires and battery cable at starter motor.
- Disconnect wiring clamp at starter support brack...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
General Motors Corp./Saturn Cars -> Check Engine Or Service Now Soon Engine Indicator Lamps (Gasoline Engines w/Electronic Engine Controls Or EFI) -> Except LeMans, Metro, Prizm, Storm & Vibe
Vehicle: 1993 Chevrolet Beretta GT 3.1 V6 GAS
The Check Engine lamp should light when the ignition is turned On. When the engine is started, the lamp should go off. If the lamp remains on for 10 seconds or constantly after the engine is started, the self diagnosis system has detected a fault condition and has stored a code in the system Electronic Control Module (ECM) or Powertrain Control Module (PCM). After diagnosis and repair, the ECM memory can be cleared of codes as follows:
On models except Cadillac with DEFI, remove the ECM/PCM fuse or disconnect the battery ground cable for approximately 30...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 1993 Chevrolet Beretta GTZ 2.3 L4 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater hose inlet clamp at engine using hose clamp pliers.
- Remove heater inlet hose from engine.
- Reposition heater core inlet hose clamp at heater core using hose clamp pliers.
- Remove hose from vehicle.
- Reverse procedure to in...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1993 Chevrolet Beretta AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1993 Chevrolet Beretta GT 3.1 V6 GAS
- Remove belt guard.
- Rotate or lift on tensioner to relieve tension from ...
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1993 Chevrolet Beretta AUTOMOBILES
Component location diagrams for most 1993 Chevrolet Beretta cars and light trucks sold in the U.S. from 1990+.
Engine Compartment Relay Bracket Diagram for 1993 Chevrolet Beretta 2.2 L4 GAS Components on diagram: |
LH Top of Engine Diagram for 1993 Chevrolet Beretta GTZ 3.1 V6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1993 Chevrolet Beretta AUTOMOBILES
OEM drawn wiring diagrams for most 1993 Chevrolet Beretta cars and light trucks sold in the U.S.
1993 Chevrolet Beretta GT 3.1 V6 GAS Wiring Diagram Components on diagram: |
1993 Chevrolet Beretta GTZ 2.3 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1993 Chevrolet Beretta AUTOMOBILES
OEM TSB listings for most 1993 Chevrolet Beretta cars and light trucks sold in the U.S. from 1985+.
Document: Car and Truck Fix It Right the First Time Issues Vehicle: 1993 Chevrolet Beretta 2.2 L4 GAS Auto Systems: |
Document: Air Conditioning Odor Vehicle: 1993 Chevrolet Beretta 2.2 L4 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1993 Chevrolet Beretta AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1993 Chevrolet Beretta cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1993 Chevrolet Beretta cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1993 Chevrolet Beretta cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1993 Chevrolet Beretta cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1993 Chevrolet Beretta SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 Chevrolet Beretta vehicle. |
Access the Complete guide! |