Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 GMC K3500 Pickup car and truck
repair procedures including GMC engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1993 GMC K3500 Pickup automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1993 GMC K3500 Pickup
- 1993 GMC K3500 Pickup Sierra 6.2 V8 DIESEL, CID:379, Fuel Injection, Aspiration:379, Engine VIN:, Desg:J
- 1993 GMC K3500 Pickup Sierra 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:K
- 1993 GMC K3500 Pickup Sierra 7.4 V8 GAS, CID:454, Fuel Injection, Aspiration:454, Engine VIN:, Desg:N
- 1993 GMC K3500 Pickup Sierra 6.5 V8 DIESEL, CID:395, Fuel Injection, Aspiration:395, Engine VIN:, Desg:F
- 1993 GMC K3500 Pickup Sierra XC 6.2 V8 DIESEL, CID:379, Fuel Injection, Aspiration:379, Engine VIN:, Desg:J
- 1993 GMC K3500 Pickup Sierra XC 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:K
- 1993 GMC K3500 Pickup Sierra XC 7.4 V8 GAS, CID:454, Fuel Injection, Aspiration:454, Engine VIN:, Desg:N
- 1993 GMC K3500 Pickup Sierra XC 6.5 V8 DIESEL, CID:395, Fuel Injection, Aspiration:395, Engine VIN:, Desg:F
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 GMC K3500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 GMC K3500 Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Install -> Remove
Vehicle: 1993 GMC K3500 Pickup Sierra 7.4 V8 GAS
Remove
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove drive axle center cap, if equipped.
- Insert a drift or large screwdriver through brake caliper into one of the brake rotor vanes in order to prevent drive axle wheel drive shaft from turning.
- Remove nut and washer from hub. Do not reuse nut. A new nut must be used when installing wheel drive shaft.
- Using axle remover tool No. J 45859 or equivalent, press wheel drive shaft from hub.
- Remove bolts securing wheel drive shaft inboard flange to output shaft flange.
- Remove drift from rotor.
- Remove stabilizer shaft li...
CLICK HERE TO GET FULL ACCESS TO 1993 GMC K3500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 GMC K3500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 GMC K3500 Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1993 GMC K3500 Pickup Sierra 6.5 V8 DIESEL
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1993 GMC K3500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 GMC K3500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 GMC K3500 Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1993 GMC K3500 Pickup Sierra 7.4 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1993 GMC K3500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 GMC K3500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 GMC K3500 Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Install -> Remove
Vehicle: 1993 GMC K3500 Pickup Sierra XC 6.5 V8 DIESEL
Remove
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove drive axle center cap, if equipped.
- Insert a drift or large screwdriver through brake caliper into one of the brake rotor vanes in order to prevent drive axle wheel drive shaft from turning.
- Remove nut and washer from hub. Do not reuse nut. A new nut must be used when installing wheel drive shaft.
- Using axle remover tool No. J 45859 or equivalent, press wheel drive shaft from hub.
- Remove bolts securing wheel drive shaft inboard flange to output shaft flange.
- Remove drift from rotor.
- Remove stabilizer shaft li...
CLICK HERE TO GET FULL ACCESS TO 1993 GMC K3500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 GMC K3500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 GMC K3500 Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1993 GMC K3500 Pickup Sierra 5.7 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1993 GMC K3500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 GMC K3500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1993 GMC K3500 Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Install -> Remove
Vehicle: 1993 GMC K3500 Pickup Sierra XC 7.4 V8 GAS
Remove
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove drive axle center cap, if equipped.
- Insert a drift or large screwdriver through brake caliper into one of the brake rotor vanes in order to prevent drive axle wheel drive shaft from turning.
- Remove nut and washer from hub. Do not reuse nut. A new nut must be used when installing wheel drive shaft.
- Using axle remover tool No. J 45859 or equivalent, press wheel drive shaft from hub.
- Remove bolts securing wheel drive shaft inboard flange to output shaft flange.
- Remove drift from rotor.
- Remove stabilizer shaft li...
CLICK HERE TO GET FULL ACCESS TO 1993 GMC K3500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1993 GMC K3500 Pickup vehicle.
|
| Access the Complete guide! |
