Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 Mitsubishi Eclipse car and truck
repair procedures including Mitsubishi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1993 Mitsubishi Eclipse automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1993 Mitsubishi Eclipse
- 1993 Mitsubishi Eclipse 1.8 L4 GAS, CC:1755, CID:107, Fuel Injection, Aspiration:107, Engine VIN:, Desg:B
- 1993 Mitsubishi Eclipse GS 1.8 L4 GAS, CC:1755, CID:107, Fuel Injection, Aspiration:107, Engine VIN:, Desg:B
- 1993 Mitsubishi Eclipse GS 2.0 L4 GAS, CC:1997, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:E
- 1993 Mitsubishi Eclipse GS 2.0 L4 GAS, CC:1997, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:F
- 1993 Mitsubishi Eclipse GSX 2.0 L4 GAS, CC:1997, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:F
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Eclipse AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Eclipse cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Bleed -> Master Cylinder Bleed
Vehicle: 1993 Mitsubishi Eclipse GS 2.0 L4 GAS
Master Cylinder Bleed
- If master cylinder has been replaced or overhauled and reservoir is empty, proceed as follows:
- Fill reservoir with clean brake fluid, then disconnect brake lines at master cylinder.
- Depress pedal slowly and hold pedal in depressed position.
- Place fingers over outlet port, then release brake pedal.
- Repeat above steps several times. Refill reservoir suitable brake fluid.
Hydraulic System Bleed
The hydraulic brake system must be bled if air has entered the system. This condition may be precipitated by low fluid level, a hydraulic fluid leak, the opening of a hydra...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Eclipse BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Eclipse AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Eclipse cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1993 Mitsubishi Eclipse 1.8 L4 GAS
The power brake unit is a vacuum assist diaphragm assembly which multiplies the force exerted on the master cylinder piston in order to increase the hydraulic pressure delivered to the wheel calipers. This effectively decreases the effort necessary to attain sufficient stopping performance.
Vacuum assist units are powered by the opposition of engine vacuum to atmospheric pressure. A piston, cylinder and flexible diaph...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Eclipse BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Eclipse AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Eclipse cars and light trucks from 1990+.
Hydraulic Brake Systems -> Diagnosis & Testing -> Except Pickup & 1993 Montero -> Pickup & 1993 Montero -> Proportioning Valve
Vehicle: 1993 Mitsubishi Eclipse GS 1.8 L4 GAS
Proportioning Valve
Except Pickup & 1993 Montero
- Connect two pressure gauges to proportioning valve, one to the output side and one to the input side, Fig. .
- Bleed system after connecting gauges.
- Depress brake pedal and ensure measured values are within specifications shown in "Hydraulic Brake System Specifications."
Pickup & 1993 Montero
- Check load proportioning valve spring length with vehicle on flat ground.
- Press load sensor lever and measure distance between spring ends, Fig. .
- On all models except 1993 Montero, distance should be between 6.93-7.05 in...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Eclipse BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Eclipse AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Eclipse cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Overhaul -> Pushrod Adjustment -> Replacement
Vehicle: 1993 Mitsubishi Eclipse 1.8 L4 GAS
Replacement
- Remove master cylinder as outlined in "Hydraulic Brake Systems."
- Disconnect vacuum hose from power brake booster.
- Remove pin connecting power brake rod with pedal.
- Remove booster attaching nuts and re...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Eclipse BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Eclipse AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Eclipse cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1993 Mitsubishi Eclipse GS 2.0 L4 GAS
The power brake unit is a vacuum assist diaphragm assembly which multiplies the force exerted on the master cylinder piston in order to increase the hydraulic pressure delivered to the wheel calipers. This effectively decreases the effort necessary to attain sufficient stopping performance.
Vacuum assist units are powered by the opposition of engine vacuum to atmospheric pressure. A piston, cylinder and flexible diaph...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Eclipse BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Eclipse AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Eclipse cars and light trucks from 1990+.
Hydraulic Brake Systems -> Diagnosis & Testing -> Except Pickup & 1993 Montero -> Pickup & 1993 Montero -> Proportioning Valve
Vehicle: 1993 Mitsubishi Eclipse 1.8 L4 GAS
Proportioning Valve
Except Pickup & 1993 Montero
- Connect two pressure gauges to proportioning valve, one to the output side and one to the input side, Fig. .
- Bleed system after connecting gauges.
- Depress brake pedal and ensure measured values are within specifications shown in "Hydraulic Brake System Specifications."
Pickup & 1993 Montero
- Check load proportioning valve spring length with vehicle on flat ground.
- Press load sensor lever and measure distance between spring ends, Fig. .
- On all models except 1993 Montero, distance should be between 6.93-7.05 in...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Eclipse BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
