Auto Parts Search
1993 Toyota Previa CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Toyota REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
Toyota -> Component Replacement & Adjustment -> BLOWER MOTOR, REPLACE -> AVALON -> CAMRY & COROLLA -> CELICA -> COOL/ICE BOX -> Denso Type -> FRONT -> Front Blower Motor -> LAND CRUISER -> MR2 -> Panasonic Type -> PASEO & TERCEL -> PICKUP, T100 & 4RUNNER -> PREVIA -> REAR -> Rear Blower Motor -> SUPRA
Vehicle: 1993 Toyota Previa DLX 2.4 L4 GAS
SUPRA
- Remove glove compartment and side air duct.
- Remove scuff plate.
- Remove floor cover.
- Remove ECM cover.
- Remove three blower motor attaching screws and the blower motor.
- Reverse procedure to install.
CELICA
- Remove glove compartment.
- Disconnect blower motor electrical connector.
- Remove three blower motor attaching screws and the blower motor.
- Reverse procedure to install.
AVALON
- Remove instrument panel lower finish panel.
- Disconnect blower motor electrical connector.
- Rem...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
HYDRAULIC BRAKE SYSTEMS -> COMPONENT REPLACEMENT -> Except Land Cruiser, Pickup & 4Runner -> Land Cruiser, Pickup & 4Runner -> Master Cylinder -> Models w/Load Sensing Proportioning Valve (LSPV) -> Models w/Proportioning & By-Pass Valve (P-BV) -> Proportioning Valve -> Wheel Cylinders
Vehicle: 1993 Toyota Previa LE 2.4 L4 GAS
Master Cylinder
- On MR2, remove luggage compartment trim cover by removing two clips after disengaging inner part of clip.
- On all models, remove brake fluid with syringe.
- On RAV4, remove air cleaner cover with air cleaner hose.
- On all models, label and disconnect brake lines using line wrench 09751-36011, 09023-00100, or equivalent. Then cap brake lines from master cylinder.
- Disconnect wire connector from brake pressure switch and then disconnect level warning switch connector, if equipped.
- Remove master cylinder to brake unit attaching nuts, then remo...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
Toyota -> Fuel Filter Replacement -> Land Cruiser, Pickup, Previa, Sequoia, Tacoma, Tundra, T100, Truck & Van -> Fuel System Pressure Relief -> Models Less Union Bolt Fuel Line Connection -> Models w/Union Bolt Fuel Line Connection -> Removal & Installation
Vehicle: 1993 Toyota Previa DLX 2.4 L4 GAS
Fuel System Pressure Relief
Models w/Union Bolt Fuel Line Connection
- Obtain the vehicle owners radio theft protection code prior to disconnecting the battery ground cable, if equipped.
- Disconnect the battery ground cable.
- Remove the fuel fill cap to release fuel tank pressure.
- Place a shop towel over the union bolt at top of fuel filter. Slowly loosen the union bolt allowing fuel pressure to bleed down.
- Whenever the union bolt is loosened to relieve fuel system pressure, always replace the bolt gasket.
Models Less Union Bolt Fuel...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1993 Toyota Previa DLX 2.4 L4 GAS
- Raise and support vehicle, then remove front wheel.
- Remove cotter pin and lock cap, then apply brakes and remove locknut.
- Loosen two lower ball joint bolts. Do not remove.
- Disconnect tie rod from steering knuckle, then remove cotter pin and nut.
- Using ball joint puller tool No. 09628-10011 or equivalent, disconnect tie rod from steering knuckle.
- Disconnect driveshaft from differential
- Disconnect steering knuckle from lo...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
Starter, Replace
Vehicle: 1993 Toyota Previa LE 2.4 L4 GAS
- Disconnect battery ground cable.
- On 4WD models, remove front propeller shaft.
- On models equipped with manual transaxle, disconnect clutch slave cylinder and position aside. Do not disconnect clutch line.
- On all models, remove battery cable to starter attaching nut.
- Remove starter electrical connector.
- On 2WD models, remove starter attaching nuts and bolts.
- Remove starter from vehi...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
Toyota -> Automatic Transmission Oil Temperature Warning Lamp ->
Vehicle: 1993 Toyota Previa LE 2.4 L4 GAS
This lamp will be illuminated when automatic transmission or transfer case fluid temperature exceeds 302°F. If the lamp lights, allow vehicle to operate at idle speed until fluid temperature falls below 248°F; t...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 1993 Toyota Previa LE 2.4 L4 GAS
Inlet
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at heater core.
- Remove hose from heater core.
- Reposition hose clamp at water outlet.
- Remove hose from water outlet.
- Remove hose from vehicle.
- Reverse procedure ...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1993 Toyota Previa AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1993 Toyota Previa DLX 2.4 L4 GAS
- Remove power steering pump drive belt.
- Raise and support vehicle.
- Remove engine under cover.
- Loosen idle pulley lock nut.
- Loos...
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1993 Toyota Previa AUTOMOBILES
Component location diagrams for most 1993 Toyota Previa cars and light trucks sold in the U.S. from 1990+.
Supplemental Restraint System Component Locations Diagram for 1993 Toyota Previa LE 2.4 L4 GAS Components on diagram: |
Emission Control System Component Locations Diagram for 1993 Toyota Previa LE 2.4 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1993 Toyota Previa AUTOMOBILES
OEM drawn wiring diagrams for most 1993 Toyota Previa cars and light trucks sold in the U.S.
1993 Toyota Previa LE 2.4 L4 GAS Wiring Diagram Components on diagram: |
1993 Toyota Previa DLX 2.4 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1993 Toyota Previa AUTOMOBILES
OEM TSB listings for most 1993 Toyota Previa cars and light trucks sold in the U.S. from 1985+.
Document: REPLACEMENT CERTIFICATION LABELS - REVISED Vehicle: 1993 Toyota Previa DLX 2.4 L4 GAS Auto Systems: |
Document: PERMANENT-TYPE PROTECTIVE WAX COATINGS Vehicle: 1993 Toyota Previa DLX 2.4 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1993 Toyota Previa AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1993 Toyota Previa cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1993 Toyota Previa cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1993 Toyota Previa cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1993 Toyota Previa cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1993 Toyota Previa SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 Toyota Previa vehicle. |
Access the Complete guide! |