1994 Dodge Shadow Brake Service (ONLINE REPAIR MANUALS)

Auto Parts Search


Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!
Help me findSearch
Get Full Access Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1994 Dodge Shadow car and truck repair procedures including Dodge engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your 1994 Dodge Shadow automobile. Try the Automotix DIY solution today!
DIY REPAIR SAMPLES > CONTINUE EXPLORING >

We have info for following modifications of 1994 Dodge Shadow

  • 1994 Dodge Shadow 2.5 L4 GAS, CC:2507, CID:153, Fuel Injection, Aspiration:153, Engine VIN:, Desg:K
  • 1994 Dodge Shadow 2.2 L4 GAS, CID:135, Fuel Injection, Aspiration:135, Engine VIN:, Desg:D
  • 1994 Dodge Shadow ES 2.5 L4 GAS, CC:2507, CID:153, Fuel Injection, Aspiration:153, Engine VIN:, Desg:K
  • 1994 Dodge Shadow ES 3.0 V6 GAS, CC:2972, CID:181, Fuel Injection, Aspiration:181, Engine VIN:, Desg:3

BRAKE SERVICE PROCEDURES FOR 1994 Dodge Shadow AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Dodge Shadow cars and light trucks from 1990+.

Power Brake Units -> Troubleshooting -> DECREASING BRAKE PEDAL TRAVEL -> DRAGGING BRAKES -> HARD BRAKE PEDAL
Vehicle: 1994 Dodge Shadow ES 3.0 V6 GAS

DECREASING BRAKE PEDAL TRAVEL

If a decreasing brake pedal is encountered, the power brake unit may be binding internally. To test the power brake unit for this condition proceed as follows:

  • Place transmission shift lever into Neutral and start engine.
  • Increase engine speed to approximately 1500 RPM, close throttle and completely depress brake pedal.
  • Slowly release brake pedal and stop engine.
  • Remove vacuum check valve and hose from power brake unit. Observe for backward movement of brake pedal.
  • If brake pedal moves backward, power brake unit has internal binding.
  • Replace power brake un...

CLICK HERE TO GET FULL ACCESS TO 1994 Dodge Shadow BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1994 Dodge Shadow AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Dodge Shadow cars and light trucks from 1990+.

Power Brake Units -> Power Brake Unit Service -> Acclaim, Daytona, Dynasty, Fifth Avenue, Imperial, LeBaron, Shadow, Spirit, Sundance & 1992-93 New Yorker -> Colt, Colt Vista, Colt Wagon, Stealth, Summit & Summit Wagon -> Concorde, Intrepid, Vision, LHS & 1994 New Yorker -> Laser & Eagle Talon -> Monaco & Eagle Premier -> POWER BOOSTER, REPLACE
Vehicle: 1994 Dodge Shadow 2.2 L4 GAS

POWER BOOSTER, REPLACE
Acclaim, Daytona, Dynasty, Fifth Avenue, Imperial, LeBaron, Shadow, Spirit, Sundance & 1992-93 New Yorker
  • Remove master cylinder attaching nuts, disconnect brake tubes between master cylinder and valve assembly, then remove master cylinder.
  • Remove clutch cable mounting bracket, if equipped.
  • Disconnect vacuum hose from check valve on power brake unit. Do not remove check valve from booster.
  • Pull wiring harness away from and up shock tower. If more slack is required, disconnect wiring harness from bulkhead connector.
  • From under instrument panel, install a...

CLICK HERE TO GET FULL ACCESS TO 1994 Dodge Shadow BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1994 Dodge Shadow AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Dodge Shadow cars and light trucks from 1990+.

Disc Brakes -> Type 6-Kelsey-Hayes Dual Pin Floating Caliper Disc Brake, Front -> Caliper Service -> Assemble -> CALIPER OVERHAUL -> CALIPER REPLACE -> Disassemble
Vehicle: 1994 Dodge Shadow 2.2 L4 GAS

CALIPER REPLACE
  • Remove caliper as outlined under "Brake Pad Service."
  • Disconnect Brake Line.
  • Reverse Procedure to install, bleed brakes as outlined under "Brake System Bleed."
CALIPER OVERHAUL
Disassemble
  • Remove caliper assembly as described under "Brake Pad, Service."
  • Place a wood block between caliper piston and caliper fingers. With brake hose attached to caliper, carefully depress brake pedal to push piston out of caliper bore. Prop brake pedal to any position below first inch of brake pedal travel to prevent brake fluid loss.
  • If piston are to be removed from both calipers, disconnect bra...

CLICK HERE TO GET FULL ACCESS TO 1994 Dodge Shadow BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1994 Dodge Shadow AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Dodge Shadow cars and light trucks from 1990+.

Disc Brakes -> Type 6-Kelsey-Hayes Dual Pin Floating Caliper Disc Brake, Front -> Brake System Bleed -> MANUAL BLEEDING -> PRESSURE BLEEDING
Vehicle: 1994 Dodge Shadow ES 3.0 V6 GAS

Bleeding the hydraulic brake system is necessary if air has entered the system. Symptoms can be noted by loss of brake operation, and/or a low or spongy brake pedal.

The hydraulic fluid is bled or flushed from the system through bleeder valves located on the calipers, wheel cylinders, and some master cylinders. When bleeding the hydraulic brake system, use only specified brake fluid. Never reuse old brake fluid removed from the system.

PRESSURE BLEEDING

Pressure bleeding is recommended for all hydraulic brake systems. It is the fastest method because the master cylinder is autom...

CLICK HERE TO GET FULL ACCESS TO 1994 Dodge Shadow BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1994 Dodge Shadow AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Dodge Shadow cars and light trucks from 1990+.

Drum Brakes -> Type 2 & 3--Kelsey-Hayes & Varga Leading Trailing Drum Brakes -> Brake Service -> INSTALLATION -> REMOVAL -> Type 2--Kelsey-Hayes -> Type 3--Varga
Vehicle: 1994 Dodge Shadow 2.5 L4 GAS

REMOVAL
  • Raise and support rear of vehicle.
  • Remove tire and wheel assembly, then remove brake drum. If brake lining is dragging on brake drum, back off brake adjustment by rotating adjustment screw.
  • Using suitable pliers, remove adjuster lever spring, Fig. .
  • Remove adjuster lever.
  • Turn automatic adjuster screw out to expand shoes past wheel cylinder boot.
  • Disconnect parking brake cable from parking brake lever.
  • On Type 2--Kelsey Hayes, using suitable tool, remove hold-down springs.
  • Pull brake shoe assembly down and away from anchor plate, then remove brake shoe springs and adjusting screw ...

CLICK HERE TO GET FULL ACCESS TO 1994 Dodge Shadow BRAKE SERVICE PROCEDURES

BRAKE SERVICE PROCEDURES FOR 1994 Dodge Shadow AUTOMOBILES

Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Dodge Shadow cars and light trucks from 1990+.

Hydraulic Brake Systems -> Component Service -> Assemble -> Cleaning & Inspection -> Disassemble -> DOUBLE FLARE/INVERTED SEAT -> HYDRAULIC TUBING -> MASTER CYLINDER -> WHEEL CYLINDER
Vehicle: 1994 Dodge Shadow ES 3.0 V6 GAS

MASTER CYLINDER

When disassembling the master cylinder, note the position of all parts as they are removed for proper installation.

When disassembled, wash all parts in denatured alcohol or clean brake fluid only. Use an air hose to blow out all passages, orifices and valve holes. Air dry and place parts on clean paper or lint-free cloth.

Inspect master cylinder bore for scoring, rust, pitting or etching. Any of these conditions will require replacement of the housing. Never hone the bore of the master cylinder as this will remove the anodized surface. Inspect master cylinder pis...

CLICK HERE TO GET FULL ACCESS TO 1994 Dodge Shadow BRAKE SERVICE PROCEDURES

Shop online for auto body parts, engines, wheels, lights...

More parts
Help me findSearch
Auto Repair Quick Search
Help me find
Search DIY repair manuals by VIN...
Vehicle Identification Number is a unique serial number used by the automotive industry to identify individual motor vehicles

Find out what info we have for your vehicle

Get the Complete Technical Service Bulletins!
Get the Complete Technical Service Bulletins!Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1994 Dodge Shadow vehicle.
Access the Complete guide!
Need To Fix Your Car or Truck?
Save Money With Free Car Insurance Quote
FREE car insurance quote
Enter Zip Code:
Auto Repair Quick Search
Help me find