Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1994 Mitsubishi Montero car and truck
repair procedures including Mitsubishi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1994 Mitsubishi Montero automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1994 Mitsubishi Montero
- 1994 Mitsubishi Montero LS 3.0 V6 GAS, CC:2972, CID:181, Fuel Injection, Aspiration:181, Engine VIN:, Desg:H
- 1994 Mitsubishi Montero SR 3.5 V6 GAS, CC:3497, CID:215, Fuel Injection, Aspiration:215, Engine VIN:, Desg:M
BRAKE SERVICE PROCEDURES FOR 1994 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Mitsubishi Montero cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Bleed -> Master Cylinder Bleed
Vehicle: 1994 Mitsubishi Montero SR 3.5 V6 GAS
Master Cylinder Bleed
- If master cylinder has been replaced or overhauled and reservoir is empty, proceed as follows:
- Fill reservoir with clean brake fluid, then disconnect brake lines at master cylinder.
- Depress pedal slowly and hold pedal in depressed position.
- Place fingers over outlet port, then release brake pedal.
- Repeat above steps several times. Refill reservoir suitable brake fluid.
Hydraulic System Bleed
The hydraulic brake system must be bled if air has entered the system. This condition may be precipitated by low fluid level, a hydraulic fluid leak, the opening of a hydra...
CLICK HERE TO GET FULL ACCESS TO 1994 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Mitsubishi Montero cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting -> Except Pickup -> General Malfunction Diagnosis -> Pickup -> Transient Malfunction Diagnosis
Vehicle: 1994 Mitsubishi Montero LS 3.0 V6 GAS
General Malfunction Diagnosis
Except Pickup
Problems related to the Anti-Lock Brake System (ABS) can generally be classified as electrical or hydraulic.
For problems in the electrical system, a self-diagnostic function is built into the Electronic Control Unit (ECU), allowing the ABS warning lamp to illuminate as a warning to the driver in the event of an abnormality. In this instance, inspections can be performed with a voltmeter, Multi-Use Tester (MUT), oscilloscope or the ABS warning lamp.
Problems with the hydraulic system can be located in the same manner as ordinary brakes. It...
CLICK HERE TO GET FULL ACCESS TO 1994 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Mitsubishi Montero cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Cleaning & Inspection -> Disassemble -> Master Cylinder -> Overhaul -> Wheel Cylinder
Vehicle: 1994 Mitsubishi Montero LS 3.0 V6 GAS
Master Cylinder
Overhaul
- Disassemble master cylinder in numbered sequence shown, Figs. and . Note the position of all parts as they are removed for proper installation.
- On models equipped with attached reservoir master cylinder, remove reservoir screw and cap, brake fluid sensor, float, then the reservoir, Fig. .
- On models equipped with separately mounted reservoir, remove nipple, Fig. .
- Use a wooden stick or dowel to depress primary piston into cylinder bore.
- On all models except Precis, with pushrod depressed, remove piston stopper bolt, the...
CLICK HERE TO GET FULL ACCESS TO 1994 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Mitsubishi Montero cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Cleaning & Inspection -> Disassemble -> Master Cylinder -> Overhaul -> Wheel Cylinder
Vehicle: 1994 Mitsubishi Montero SR 3.5 V6 GAS
Master Cylinder
Overhaul
- Disassemble master cylinder in numbered sequence shown, Figs. and . Note the position of all parts as they are removed for proper installation.
- On models equipped with attached reservoir master cylinder, remove reservoir screw and cap, brake fluid sensor, float, then the reservoir, Fig. .
- On models equipped with separately mounted reservoir, remove nipple, Fig. .
- Use a wooden stick or dowel to depress primary piston into cylinder bore.
- On all models except Precis, with pushrod depressed, remove piston stopper bolt, the...
CLICK HERE TO GET FULL ACCESS TO 1994 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Mitsubishi Montero cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Overhaul -> Pushrod Adjustment -> Replacement
Vehicle: 1994 Mitsubishi Montero SR 3.5 V6 GAS
Replacement
- Remove master cylinder as outlined in "Hydraulic Brake Systems."
- Disconnect vacuum hose from power brake booster.
- Remove pin connecting power brake rod with pedal.
- Remove booster attaching nuts and re...
CLICK HERE TO GET FULL ACCESS TO 1994 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Mitsubishi Montero cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Bleed -> Master Cylinder Bleed
Vehicle: 1994 Mitsubishi Montero LS 3.0 V6 GAS
Master Cylinder Bleed
- If master cylinder has been replaced or overhauled and reservoir is empty, proceed as follows:
- Fill reservoir with clean brake fluid, then disconnect brake lines at master cylinder.
- Depress pedal slowly and hold pedal in depressed position.
- Place fingers over outlet port, then release brake pedal.
- Repeat above steps several times. Refill reservoir suitable brake fluid.
Hydraulic System Bleed
The hydraulic brake system must be bled if air has entered the system. This condition may be precipitated by low fluid level, a hydraulic fluid leak, the opening of a hydra...
CLICK HERE TO GET FULL ACCESS TO 1994 Mitsubishi Montero BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1994 Mitsubishi Montero vehicle.
|
| Access the Complete guide! |
