Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1994 Subaru Impreza car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1994 Subaru Impreza automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1994 Subaru Impreza
- 1994 Subaru Impreza 1.8 H4 GAS, CC:1781, Fuel Injection, Engine VIN:, Desg:2
- 1994 Subaru Impreza L 1.8 H4 GAS, CC:1781, Fuel Injection, Engine VIN:, Desg:2
- 1994 Subaru Impreza LS 1.8 H4 GAS, CC:1781, Fuel Injection, Engine VIN:, Desg:2
BRAKE SERVICE PROCEDURES FOR 1994 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Subaru Impreza cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Dual Proportioning Valve -> Master Cylinder
Vehicle: 1994 Subaru Impreza LS 1.8 H4 GAS
Master Cylinder
- Disconnect brake lines from master cylinder and plug the ends.
- If applicable, disconnect fluid warning switch electrical connector.
- Remove master cylinder retaining nuts and the master cylinder.
- Reverse procedure to install.
- Bleed hydraulic system after completing installation.
Dual Proportioning Valve
Inspect brake line connections at DPV for fluid le...
CLICK HERE TO GET FULL ACCESS TO 1994 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Subaru Impreza cars and light trucks from 1990+.
Anti-lock Brakes -> Impreza & 1995 Legacy Less TCS -> System Service -> ABS Control Module -> ABS Hydraulic Unit -> Brake System Bleed -> Component Replacement -> Front Sensor -> G Sensor -> Rear Sensor
Vehicle: 1994 Subaru Impreza LS 1.8 H4 GAS
Brake System Bleed
Two technicians are required to bleed the brake system. Brake pedal operation must be very slow. Keep brake fluid reserve tank topped off to prevent entry of air into brake system during bleeding procedure. Check entire brake system for fluid leaks.
- Start with brakes connected to secondary chamber of master cylinder first.
- Fit one end of a vinyl tube onto air bleeder and place other end of tube into a container of brake fluid.
- Slowly depress brake pedal and keep it depressed, then open air bleeder for 1 to 2 seconds.
- Close air bleeder and slowly release brake pedal.
- ...
CLICK HERE TO GET FULL ACCESS TO 1994 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Subaru Impreza cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> Drum Brake -> Parking Brake
Vehicle: 1994 Subaru Impreza L 1.8 H4 GAS
Parking Brake
- On models except Impreza, pull parking brake lever three to five times. Mechanism should click six to seven times when a force of 55 lbs. is exerted on the lever.
- On Impreza, pull parking brake lever three to five times. Mechanism should click six times when a force of 44 lbs. is exerted on the lever.
- On Loyale, if lever operation is not as specified, rotate the equalizer cable adjustment nut until play at " A" in Fig. , is set at 0-.02 inch (0-.5mm).
- On Justy, if lever operation is not as specified, adjust lever stroke at parking brake rod until ...
CLICK HERE TO GET FULL ACCESS TO 1994 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Subaru Impreza cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 1994 Subaru Impreza LS 1.8 H4 GAS
Master Cylinder
- Remove master cylinder from vehicle.
- Remove secondary piston stopper screw with screwdriver as shown in Fig. .
- Push piston inward, then remove snap ring.
- Apply pressure to piston assembly while Inserting a small screwdriver into window of piston retainer and raise piston retainer latch as shown in Fig. .
- Remove primary and secondary piston assemblies. Do not disassemble pistons. if disassembled, the spring settings will change.
- Inspect master cylinder inside diameter to piston clearance, Service limit is not to exceed 0.043 inch.
- Clean...
CLICK HERE TO GET FULL ACCESS TO 1994 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Subaru Impreza cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Impreza & Legacy -> Justy -> Loyale
Vehicle: 1994 Subaru Impreza 1.8 H4 GAS
Loyale
- Raise and support vehicle, then remove rear wheels.
- Remove brake drum, then disconnect brake line from back plate.
- Using suitable pliers, remove shoe hold-down springs, Figs. and .
- Remove shoes.
- Reverse procedure to install. Refer to Fig. , for tightening specifications.
Impreza & Legacy
- Raise and support vehicle, then remove rear wheels.
- Remove brake drum. If difficult to remove brake drum, remove adjusting hole cover from back plate, then turn adjusting screw until shoe separate from drum.
- Remove hold-down pin and cup.
- Disconnect lower shoe return spring from shoes.
- Remove s...
CLICK HERE TO GET FULL ACCESS TO 1994 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Subaru Impreza cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> Drum Brake -> Parking Brake
Vehicle: 1994 Subaru Impreza 1.8 H4 GAS
Parking Brake
- On models except Impreza, pull parking brake lever three to five times. Mechanism should click six to seven times when a force of 55 lbs. is exerted on the lever.
- On Impreza, pull parking brake lever three to five times. Mechanism should click six times when a force of 44 lbs. is exerted on the lever.
- On Loyale, if lever operation is not as specified, rotate the equalizer cable adjustment nut until play at " A" in Fig. , is set at 0-.02 inch (0-.5mm).
- On Justy, if lever operation is not as specified, adjust lever stroke at parking brake rod until ...
CLICK HERE TO GET FULL ACCESS TO 1994 Subaru Impreza BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1994 Subaru Impreza vehicle.
|
| Access the Complete guide! |
