Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1994 Suzuki Swift car and truck
repair procedures including Suzuki engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1994 Suzuki Swift automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1994 Suzuki Swift
- 1994 Suzuki Swift GA 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1994 Suzuki Swift GS 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1994 Suzuki Swift GT 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
- 1994 Suzuki Swift L 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:3
BRAKE SERVICE PROCEDURES FOR 1994 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Adjustments -> Brake Pedal Height -> Brake Pedal Travel Check
Vehicle: 1994 Suzuki Swift GT 1.3 L4 GAS
Brake Pedal Height
The brake pedal should be at the same height as clutch pedal. Ensure distance between brake booster mounting surface (with gasket) and pushrod clevis pin hole is as follows:
- On Samurai models, 4.94-4.98 inches (125.5-126.5 mm)
- On 1993-95 Sidekick models, 6.60-6.64 inches (167.6-168.6 mm)
- On Swift models, 4.51-4.54 inches (114.5-115.5 mm).
Brake Pedal Travel Check
- Start engine, then depress brake pedal a few times.
- Apply approximately 66 lbs. load to brake pedal, and measu...
CLICK HERE TO GET FULL ACCESS TO 1994 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Suzuki Swift cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Brake Booster Overhaul -> Esteem & 1996 Sidekick & X-90 -> Power Brake Unit, Replace -> Samurai, Swift & 1993-95 Sidekick
Vehicle: 1994 Suzuki Swift GS 1.3 L4 GAS
Power Brake Unit, Replace
- Remove master cylinder from booster as outlined under " Master Cylinder, Replace," in "Hydraulic Brakes".
- Disconnect pushrod clevis from brake pedal arm.
- Disconnect vacuum hose from booster.
- Remove booster attaching nuts, then the booster assembly.
- Reverse procedure to install, then ensure brake pedal height and pedal travel is correct as outlined under "Brake Pedal Height, Adjust," and "Brake Pedal Travel Check" in "Hydraulic Brakes" .
Brake Booster Overhaul
Samurai, Swift & 1993-95 Sidekick
Refer to Figs. through , when performing this procedure.
- Remove piston...
CLICK HERE TO GET FULL ACCESS TO 1994 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting -> Brake Pull -> Brake Warning Light On Or Flashing, After Engine Start -> Brake Warning Light On, w/Brake Pedal Applied -> Dragging Brakes -> Excessive Pedal Travel -> Low Braking Force
Vehicle: 1994 Suzuki Swift GT 1.3 L4 GAS
Low Braking Force
- Fluid leakage from brake lines and/or hoses.
- Air in brake system.
- Malfunctioning wheel cylinder and/or caliper assembly.
Brake Pull
- Malfunctioning wheel cylinder and/or caliper assembly.
- Loose calipers.
- Restricted brake line or hose.
Excessive Pedal Travel
- Partial brake system failure.
- Insufficient fluid in master cylinder reservoirs.
- Air in system.
Dragging Brakes
- Master c...
CLICK HERE TO GET FULL ACCESS TO 1994 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Suzuki Swift cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Brake Drum, Replace -> Brake Shoe, Replace -> Esteem -> Esteem & Swift -> Samurai -> Sidekick & X-90 -> Swift -> Wheel Cylinder, Replace
Vehicle: 1994 Suzuki Swift L 1.3 L4 GAS
Brake Drum, Replace
Samurai
- Raise and support vehicle
- Remove wheel center cap.
- Remove rear wheel assembly. Ensure parking brake lever is not pulled up.
- Increase the clearance between brake shoe and drum by removing parking brake shoe lever return spring, then disconnect parking brake cable joint from parking brake shoe lever, Fig. .
- Remove parking brake shoe lever stopper plate, Fig. .
- Remove drum to axle hub attaching bolts, then using slide hammer tool No. 09942-15510, or equivalent, and brake drum remover tool No. 09943-35511, or equivalent, pull off brake drum.
- Re...
CLICK HERE TO GET FULL ACCESS TO 1994 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Esteem & Swift -> Master Cylinder Bleeding -> Samurai, Sidekick & X-90 -> System Bleeding
Vehicle: 1994 Suzuki Swift GA 1.3 L4 GAS
Brake fluid is extremely damaging to paint. If fluid should accidentally touch painted surface, immediately wipe fluid from paint and clean painted surface.
System Bleeding
Samurai, Sidekick & X-90
On Samurai models, bleeding is required at four places; both front wheels, P & B valve and left rear wheel cylinder, Fig. .
On Sidekick and X-90 models, bleeding is required at four places; both front wheels, pressure limit valve and left rear wheel cylinder, Fig. .
Esteem & Swift
The hydraulic lines of the brake system are based on a diagonal split system. When a brake line or hose is...
CLICK HERE TO GET FULL ACCESS TO 1994 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder, Replace
Vehicle: 1994 Suzuki Swift GT 1.3 L4 GAS
Master Cylinder, Replace
- Clean any dirt from around reservoir cap. Remove cap, then drain brake fluid into appropriate container.
- Remove reservoir connector screw, Fig. , then the reservoir.
- Disconnect brake lines from master cylinder. Do not allow brake fluid to get on painted surfaces.
- Remove master cylinder attaching bolts, then the master cylinder.
- Adjust clearance of booster piston rod to master cylinder piston as follows:
- Push piston rod several times to ensure reaction disc is in place.
- Measure with gasket in place on master cylinder and booster at atmospheric pressu...
CLICK HERE TO GET FULL ACCESS TO 1994 Suzuki Swift BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
