Auto Parts Search
1996 Infiniti J30 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Infiniti REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Infiniti -> Automatic Temperature Control System Diagnosis & Testing, J30 -> A/C Component Diagnosis & Testing -> A/C Pressure Switch -> A/C Relay -> Ambient Sensor -> Blower Motor -> Dual Pressure Switch -> HI Relay -> In-Vehicle Sensor -> Intake Sensor -> Potentiometer Balance Resistor (PBR) -> Sunload Sensor -> Triple Pressure Switch
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
A/C Pressure Switch
- Conduct continuity test while measuring pressure.
- When high pressure side line pressure is decreasing to 178-192 psi continuity should not exist and increasing to 206-220 psi continuity should exist.
A/C Relay
Ensure circuit continuity between terminals by supplying 12 volts to coil side terminal of A/C relay.
Ambient Sensor
- Disconnect ambient sensor connector.
- Measure resistance between terminals 1 and 2 at sensor harness side.
- Refer to Fig. for resistance specifications.
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Power Brake Units -> Power Brake Unit Service -> Overhaul -> Replacement
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
Replacement
- Connect tube to any bleeder valve.
- Open bleeder valve, drain fluid by depressing brake pedal until master cylinder is empty, repeat for second circuit.
- Remove brake line flare nuts, then master cylinder attaching nuts.
- Remove clevis pin, Figs. through .
- Remove brake booster attaching nuts, then remove booster.
- Reverse procedure to install noting the following:
- ...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Infiniti -> Fuel Filter Replacement -> All Models -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveabilty symptoms may occur. The vehicle may need to be driven 10...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
- Disconnect the ABS wheel sensors, located at the hubs and final drive unit, to prevent sensors from being damaged.
- Remove side flange mounting bolts and separate driveshaft from final drive.
- Remove hub nut, then lightly tap on driveshaft...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Alternator, Replace
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
- Remove righthand engine undercover.
- Remove righthand side inspection cover.
- Loosen belt idler pulley.
- Remove drive belt.
- Remove A/C compressor mounting bolts.
- Remove cooling fan and fan shroud.
- Slide A/C compressor forward.
- Disconnect alternator harness connector.
- Remov...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Infiniti -> Traction Control/Slip Indicator Lamp ->
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
Drive wheel slippage is detected by the four wheel rotating signal. When wheel slip becomes excessive, the Traction Control System (TCS) operates causing the SLIP indicator lamp to illuminate. When the TCS off switch is used to cancel TCS function, the ...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at thermostat housing.
- Remove hose from thermostat housing.
- Remove hose from vehicle.
- Reverse pr...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1996 Infiniti J30 AUTOMOBILES
Serpentine Drive Belt, Replace -> Air Conditioning -> Alternator -> Power Steering
Vehicle: 1996 Infiniti J30 3.0 V6 GAS
Alternator
- Disconnect battery ground cable from battery.
- Loosen alternator upper locknut.
- Loosen lower mounting nut.
- Push alternator inward toward engine.
- Remove alternator drive belt.
- Clean and inspect belt surfaces of all pulleys.
- Reverse procedure to install, noting the following:
- Torque alternator idler pulley adjusting nut to 23 ft. lbs.
Air Conditioning
- Disconnect battery ground cable from batter...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1996 Infiniti J30 AUTOMOBILES
Component location diagrams for most 1996 Infiniti J30 cars and light trucks sold in the U.S. from 1990+.
Door Wiring Harness Connector Locations Diagram for 1996 Infiniti J30 3.0 V6 GAS Components on diagram: |
Air Bag Wiring Harness Connector Locations Diagram for 1996 Infiniti J30 3.0 V6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1996 Infiniti J30 AUTOMOBILES
OEM drawn wiring diagrams for most 1996 Infiniti J30 cars and light trucks sold in the U.S.
1996 Infiniti J30 3.0 V6 GAS Wiring Diagram Components on diagram: |
1996 Infiniti J30 3.0 V6 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1996 Infiniti J30 AUTOMOBILES
OEM TSB listings for most 1996 Infiniti J30 cars and light trucks sold in the U.S. from 1985+.
Document: A/C System O-Ring Seal Leaks Vehicle: 1996 Infiniti J30 3.0 V6 GAS Auto Systems: |
Document: Windshield Cracking Vehicle: 1996 Infiniti J30 3.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1996 Infiniti J30 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1996 Infiniti J30 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1996 Infiniti J30 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1996 Infiniti J30 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1996 Infiniti J30 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti J30 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1996 Infiniti J30 vehicle. |
Access the Complete guide! |