Auto Parts Search

BRAKE SERVICE PROCEDURES FOR 1997 BMW 328IC AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 BMW 328IC cars and light trucks from 1990+.
Anti-lock Brakes -> Precautions -> Battery Ground Cable
Vehicle: 1997 BMW 328IC 2.8 L6 GAS
Battery Ground Cable
Prior to service, dis...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW 328IC BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 BMW 328IC AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 BMW 328IC cars and light trucks from 1990+.
Hydraulic Brake Systems -> Hydraulic Brake System Specifications
Vehicle: 1997 BMW 328IC 2.8 L6 GAS
CLICK HERE TO GET FULL ACCESS TO 1997 BMW 328IC BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 BMW 328IC AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 BMW 328IC cars and light trucks from 1990+.
Anti-lock Brakes -> Description -> ABS Less Stability & Traction Control -> ABS w/Stability & Traction Control
Vehicle: 1997 BMW 328IC 2.8 L6 GAS
ABS Less Stability & Traction Control
The Anti-Lock Brake System (ABS) consists of a control unit, hydraulic unit, speed sensors and wiring harness, Fig. , Each speed sensor has a gear wheel which runs past the permanently magnetized edge of the speed sensor installed in the wheel hub. The rotary motion of the wheels is recorded by inductive sensors and an electric signal is sent to the electronic control unit.
The electronic control unit is located in a compartment on the right side of the engine compartment. This control unit inputs acceleration, deceleration and slip factors from ...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW 328IC BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 BMW 328IC AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 BMW 328IC cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Assemble -> Disassemble -> Front -> Inspection -> Overhaul -> Rear -> Replace
Vehicle: 1997 BMW 328IC 2.8 L6 GAS
Replace
Front
- Raise and support vehicle, then remove front tire and wheel.
- Drain moderate amount of brake fluid from reservoir using suitable syringe.
- Disconnect caliper brake hose.
- Remove caliper bolts and disconnect brake pad wear sensor electrical connector.
- Remove caliper toward rear.
- Reverse procedure to install, noting the following:
- Tighten mounting bolts to specifications.
- Bleed brake system.
- Ensure brake pad wear sensor wire does not contact rotor or wheel.
Rear
- Raise and support vehicle, then remove rear tire and wheel assembly.
- Drain moderate amount of brake fluid from reservoir u...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW 328IC BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 BMW 328IC AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 BMW 328IC cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> Brake System Bleed -> Component Replacement -> Control Unit, Replace -> Front Speed Sensor, Replace -> Hydraulic Unit, Replace -> Rear Speed Sensor, Replace
Vehicle: 1997 BMW 328IC 2.8 L6 GAS
Brake System Bleed
Refer to "Hydraulic Brake Systems," for procedures.
Component Replacement
Hydraulic Unit, Replace
- Remove coolant expansion tank.
- Remove brake lines from hydraulic unit as follows: front left; front right; rear left; rear right.
- Remove brake hydraulic lines from master cylinder to hydraulic unit.
- Remove hydraulic cover, then loosen, but do not remove, unit mounting bolts.
- Remove mounting screws, then disconnect multiple pin connector and ground wire.
- Remove hydraulic unit by pulling front up and disconnecting rear.
- Reverse procedure to install. Ensuring hydraulic lines are ...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW 328IC BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 BMW 328IC AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 BMW 328IC cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1997 BMW 328IC 2.8 L6 GAS
Ensure traction control systems are turned Off prior to bleeding brake system.
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to righthand rear wheel. Bleed until no bubbles appear.
- Repeat previous step for lefthand rear, righthand front and lefthand front wheels.
- Support rear suspension at wheel carriers and lower car so rear suspension compresses to its normal loaded position (to prevent damage to output shaft joints). Wheel...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW 328IC BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |