Auto Parts Search
We have info for following modifications of 1997 Chevrolet K1500 Pickup
- 1997 Chevrolet K1500 Pickup 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:R
- 1997 Chevrolet K1500 Pickup 4.3 V6 GAS, CID:262, Fuel Injection, Aspiration:262, Engine VIN:, Desg:W
- 1997 Chevrolet K1500 Pickup 6.5 V8 DIESEL, CID:395, Fuel Injection, Aspiration:395, Engine VIN:, Desg:S
- 1997 Chevrolet K1500 Pickup 5.0 V8 GAS, CID:305, Fuel Injection, Aspiration:305, Engine VIN:, Desg:M
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Chevrolet K1500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Chevrolet K1500 Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 Chevrolet K1500 Pickup 5.0 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1997 Chevrolet K1500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Chevrolet K1500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Chevrolet K1500 Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1997 Chevrolet K1500 Pickup 5.0 V8 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove drive axle center cap, if equipped.
- Insert a drift or large screwdriver through brake caliper into one of the brake rotor vanes in order to prevent drive axle wheel drive shaft from turning.
- Remove nut and washer from hub. Do not reuse nut. A new nut must be used when installing wheel drive shaft.
- Using axle remover tool No. J 45859 or equivalent, press wheel drive shaft from hub.
- Remove bolts securing wheel dr...
CLICK HERE TO GET FULL ACCESS TO 1997 Chevrolet K1500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Chevrolet K1500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Chevrolet K1500 Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 Chevrolet K1500 Pickup 5.7 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1997 Chevrolet K1500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Chevrolet K1500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Chevrolet K1500 Pickup cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 Chevrolet K1500 Pickup 6.5 V8 DIESEL
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1997 Chevrolet K1500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Chevrolet K1500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Chevrolet K1500 Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1997 Chevrolet K1500 Pickup 5.7 V8 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove drive axle center cap, if equipped.
- Insert a drift or large screwdriver through brake caliper into one of the brake rotor vanes in order to prevent drive axle wheel drive shaft from turning.
- Remove nut and washer from hub. Do not reuse nut. A new nut must be used when installing wheel drive shaft.
- Using axle remover tool No. J 45859 or equivalent, press wheel drive shaft from hub.
- Remove bolts securing wheel dr...
CLICK HERE TO GET FULL ACCESS TO 1997 Chevrolet K1500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Chevrolet K1500 Pickup AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Chevrolet K1500 Pickup cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1997 Chevrolet K1500 Pickup 6.5 V8 DIESEL
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove drive axle center cap, if equipped.
- Insert a drift or large screwdriver through brake caliper into one of the brake rotor vanes in order to prevent drive axle wheel drive shaft from turning.
- Remove nut and washer from hub. Do not reuse nut. A new nut must be used when installing wheel drive shaft.
- Using axle remover tool No. J 45859 or equivalent, press wheel drive shaft from hub.
- Remove bolts securing wheel dr...
CLICK HERE TO GET FULL ACCESS TO 1997 Chevrolet K1500 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 Chevrolet K1500 Pickup vehicle. |
Access the Complete guide! |