Auto Parts Search
We have info for following modifications of 1997 Chrysler Sebring
- 1997 Chrysler Sebring LX 2.0 L4 GAS, CC:1996, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:Y
- 1997 Chrysler Sebring LX 2.5 V6 GAS, CC:2497, CID:152, Fuel Injection, Aspiration:152, Engine VIN:, Desg:N
- 1997 Chrysler Sebring JX 2.4 L4 GAS, CC:2429, CID:148, Fuel Injection, Aspiration:148, Engine VIN:, Desg:X
- 1997 Chrysler Sebring JX 2.5 V6 GAS, CC:2497, CID:152, Fuel Injection, Aspiration:152, Engine VIN:, Desg:H
- 1997 Chrysler Sebring JXI 2.4 L4 GAS, CC:2429, CID:148, Fuel Injection, Aspiration:148, Engine VIN:, Desg:X
- 1997 Chrysler Sebring JXI 2.5 V6 GAS, CC:2497, CID:152, Fuel Injection, Aspiration:152, Engine VIN:, Desg:H
- 1997 Chrysler Sebring LXI 2.5 V6 GAS, CC:2497, CID:152, Fuel Injection, Aspiration:152, Engine VIN:, Desg:N
BRAKE SERVICE PROCEDURES FOR 1997 Chrysler Sebring AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Chrysler Sebring cars and light trucks from 1990+.
Disc Brakes -> Type 3-Allied Signal Dual Pin Floating Caliper Disc Brake, Front -> Caliper Service -> Overhaul -> Replacement
Vehicle: 1997 Chrysler Sebring JX 2.5 V6 GAS
Replacement
- Raise and support vehicle.
- Remove front wheel and tire assembly.
- Remove two caliper to steering knuckle guide pin bolts.
- Remove brake caliper from steering knuckle as follows:
- Rotate bottom end of caliper away from knuckle.
- Slide top of caliper down from machined abutment on steering knuckle.
- Support caliper to prevent weight from being applied to brake hose.
Overhaul
- Remove caliper from brake rotor and brake pads from caliper as described in "Brake Pad Service."
- Hang caliper on a wire away from rotor.
- Place a small piece of wood between piston and caliper fingers.
- Carefully depre...
CLICK HERE TO GET FULL ACCESS TO 1997 Chrysler Sebring BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Chrysler Sebring AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Chrysler Sebring cars and light trucks from 1990+.
Drum Brakes -> Type 2-Leading-Trailing Drum Brakes -> Adjustments -> Parking Brake
Vehicle: 1997 Chrysler Sebring LXI 2.5 V6 GAS
Parking Brake
These brakes are equipped with self adjusting mechanisms, periodic adjustments are not necessary. If stopping power is insufficient, or if brake pedal travel is excessive, brakes and self adjusting mechanism should be cleaned and inspected.
After performing brake service, adjust parking brake as follows:
- Apply parking brake lever with a force of approximately 45 lbs. while counting number of clicks. Lever should click five to seven times.
- If not within specifications, release parking brake lever and ...
CLICK HERE TO GET FULL ACCESS TO 1997 Chrysler Sebring BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Chrysler Sebring AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Chrysler Sebring cars and light trucks from 1990+.
Anti-Lock Brakes -> Type 3-Anti-Lock Braking System -> System Service -> 1997 -> 1998 -> ABS ECU -> Component Replacement -> Hydraulic Control Unit (HCU) -> Wheel Speed Sensors
Vehicle: 1997 Chrysler Sebring LX 2.0 L4 GAS
Component Replacement
Hydraulic Control Unit (HCU)
The hydraulic unit must not be disassembled, its nuts and bolts must not be loosened. Do not drop or subject the hydraulic unit to any impact shocks. Do not turn hydraulic unit upside down or lay unit on its side.
- Drain brake fluid from fluid reservoir.
- Remove lefthand fender inner splash shield.
- Remove lefthand headlamp assembly.
- On models less turbo, remove air cleaner assembly, ECM and relay box bracket.
- On models with turbo, remove power steering oil reservoir mounting bolts, then power steering pressure and return pipe clamp mounti...
CLICK HERE TO GET FULL ACCESS TO 1997 Chrysler Sebring BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Chrysler Sebring AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Chrysler Sebring cars and light trucks from 1990+.
Disc Brakes -> Type 2-MR45S, MR45V & MR58V Dual Pin Floating Caliper Disc Brake, Rear -> Caliper Service -> Overhaul -> Replacement
Vehicle: 1997 Chrysler Sebring LX 2.0 L4 GAS
Replacement
- Raise and support vehicle, then remove wheel assembly.
- Disconnect brake hose.
- Remove brake assembly attaching bolts, then the brake assembly.
- Remove brake pads and shims, then separate caliper body from caliper support, Fig. .
- Reverse procedure to install.
Overhaul
- Remove caliper assembly as described under "Caliper Replace."
- Remove caliper support, Fig. .
- Remove pin boots and boot ring.
- Position a suitable wood block in caliper body, then apply compressed air through the brake hose fitting hole to remove piston and dust boot. Apply air gently.
- Using finger tip, remove piston sea...
CLICK HERE TO GET FULL ACCESS TO 1997 Chrysler Sebring BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Chrysler Sebring AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Chrysler Sebring cars and light trucks from 1990+.
Anti-Lock Brakes -> Type 2-Bendix ABX-4 Anti-Lock Braking System -> Description -> ABS Warning Lamp -> Controller Anti-Lock Brake (CAB) -> Hydraulic Control Unit (HCU) -> Master Cylinder & Power Brake Booster -> System Components -> System Operation -> Wheel Speed Sensors
Vehicle: 1997 Chrysler Sebring JX 2.4 L4 GAS
System Operation
Under normal braking conditions, the Anti-Lock Brake System (ABS) functions as a standard brake system with a diagonally split master cylinder and conventional brake booster.
If a wheel lock is detected during braking, the system will enter ABS mode. During ABS mode, hydraulic pressure in the four wheel circuits is modulated to prevent any wheel from locking.
Each wheel circuit has a set of electrical valves to provide modulation to each wheel. Front wheels receive separate signals and rear wheels receive the same signal.
System Components
Controller Anti-Lock Brake (CAB...
CLICK HERE TO GET FULL ACCESS TO 1997 Chrysler Sebring BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Chrysler Sebring AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Chrysler Sebring cars and light trucks from 1990+.
Drum Brakes -> Type 2-Leading-Trailing Drum Brakes -> Adjustments -> Parking Brake
Vehicle: 1997 Chrysler Sebring LX 2.5 V6 GAS
Parking Brake
These brakes are equipped with self adjusting mechanisms, periodic adjustments are not necessary. If stopping power is insufficient, or if brake pedal travel is excessive, brakes and self adjusting mechanism should be cleaned and inspected.
After performing brake service, adjust parking brake as follows:
- Apply parking brake lever with a force of approximately 45 lbs. while counting number of clicks. Lever should click five to seven times.
- If not within specifications, release parking brake lever and ...
CLICK HERE TO GET FULL ACCESS TO 1997 Chrysler Sebring BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 Chrysler Sebring vehicle. |
Access the Complete guide! |