Auto Parts Search
We have info for following modifications of 1997 GMC G35/G3500 VAN
- 1997 GMC G35/G3500 VAN Savana 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:R
- 1997 GMC G35/G3500 VAN Savana 6.5 V8 DIESEL, CID:395, Fuel Injection, Aspiration:395, Engine VIN:, Desg:F
- 1997 GMC G35/G3500 VAN Savana 7.4 V8 GAS, CID:454, Fuel Injection, Aspiration:454, Engine VIN:, Desg:J
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 GMC G35/G3500 VAN AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 GMC G35/G3500 VAN cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 GMC G35/G3500 VAN Savana 6.5 V8 DIESEL
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1997 GMC G35/G3500 VAN DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 GMC G35/G3500 VAN AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 GMC G35/G3500 VAN cars and light trucks from 1990+.
DRIVESHAFT, Replace -> One Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 1997 GMC G35/G3500 VAN Savana 5.7 V8 GAS
One Piece Driveshaft
- Raise and support vehicle.
- Mark rear universal joint to drive shaft flange.
- Remove retaining bolts and clamps.
- Remove propeller shaft from pinion drive flange.
- Remove propeller shaft from transmission/transfer case.
- Using tape or a rubber band, wrap the U-Joint bearing caps to ensure bearing caps do not separate from U-Joint.
- Reverse procedure to install, noting the following:
- Align reference marks made during removal.
- Torque yoke retainer bolts to 18 ft. lbs.
Two Piece Driveshaft
- Raise and support vehicle.
- Suppor...
CLICK HERE TO GET FULL ACCESS TO 1997 GMC G35/G3500 VAN DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 GMC G35/G3500 VAN AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 GMC G35/G3500 VAN cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 GMC G35/G3500 VAN Savana 5.7 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1997 GMC G35/G3500 VAN DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 GMC G35/G3500 VAN AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 GMC G35/G3500 VAN cars and light trucks from 1990+.
DRIVESHAFT, Replace -> One Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 1997 GMC G35/G3500 VAN Savana 7.4 V8 GAS
One Piece Driveshaft
- Raise and support vehicle.
- Mark rear universal joint to drive shaft flange.
- Remove retaining bolts and clamps.
- Remove propeller shaft from pinion drive flange.
- Remove propeller shaft from transmission/transfer case.
- Using tape or a rubber band, wrap the U-Joint bearing caps to ensure bearing caps do not separate from U-Joint.
- Reverse procedure to install, noting the following:
- Align reference marks made during removal.
- Torque yoke retainer bolts to 18 ft. lbs.
Two Piece Driveshaft
- Raise and support vehicle.
- Suppor...
CLICK HERE TO GET FULL ACCESS TO 1997 GMC G35/G3500 VAN DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 GMC G35/G3500 VAN AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 GMC G35/G3500 VAN cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 GMC G35/G3500 VAN Savana 7.4 V8 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1997 GMC G35/G3500 VAN DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 GMC G35/G3500 VAN AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 GMC G35/G3500 VAN cars and light trucks from 1990+.
DRIVESHAFT, Replace -> One Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 1997 GMC G35/G3500 VAN Savana 6.5 V8 DIESEL
One Piece Driveshaft
- Raise and support vehicle.
- Mark rear universal joint to drive shaft flange.
- Remove retaining bolts and clamps.
- Remove propeller shaft from pinion drive flange.
- Remove propeller shaft from transmission/transfer case.
- Using tape or a rubber band, wrap the U-Joint bearing caps to ensure bearing caps do not separate from U-Joint.
- Reverse procedure to install, noting the following:
- Align reference marks made during removal.
- Torque yoke retainer bolts to 18 ft. lbs.
Two Piece Driveshaft
- Raise and support vehicle.
- Suppor...
CLICK HERE TO GET FULL ACCESS TO 1997 GMC G35/G3500 VAN DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 GMC G35/G3500 VAN vehicle. |
Access the Complete guide! |