Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1997 Isuzu Trooper car and truck
repair procedures including Isuzu engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1997 Isuzu Trooper automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1997 Isuzu Trooper
- 1997 Isuzu Trooper LS 3.2 V6 GAS, CC:3165, Fuel Injection, Engine VIN:, Desg:V
- 1997 Isuzu Trooper S 3.2 V6 GAS, CC:3165, Fuel Injection, Engine VIN:, Desg:V
- 1997 Isuzu Trooper LTD 3.2 V6 GAS, CC:3165, Fuel Injection, Engine VIN:, Desg:V
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Trooper AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Trooper cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1997 Isuzu Trooper LS 3.2 V6 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark companion flange on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove exhaust and transfer protectors.
- Remove bolts and then remove driveline from front final drive and transfer case.
- Reverse procedure to install noting the following:
- Torque driveline to transfer companion flange mounting bolts to 46 ...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Trooper DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Trooper AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Trooper cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1997 Isuzu Trooper LS 3.2 V6 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove drain plug from differential and drain in suitable container.
- Remove brake caliper bolt and support caliper with mechanics wire.
- On models equipped with ABS sensor, remove bolt securing anti-lock brake speed sensor.
- Remove hub assembly.
- Remove steering link and arm assembly.
- Remove suspension crossmember.
- Remove driveline.
- Remove driveline protector.
- Remove breather hose clips from front driveaxle and ...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Trooper DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Trooper AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Trooper cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1997 Isuzu Trooper S 3.2 V6 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove drain plug from differential and drain in suitable container.
- Remove brake caliper bolt and support caliper with mechanics wire.
- On models equipped with ABS sensor, remove bolt securing anti-lock brake speed sensor.
- Remove hub assembly.
- Remove steering link and arm assembly.
- Remove suspension crossmember.
- Remove driveline.
- Remove driveline protector.
- Remove breather hose clips from front driveaxle and ...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Trooper DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Trooper AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Trooper cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1997 Isuzu Trooper LS 3.2 V6 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with a...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Trooper DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Trooper AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Trooper cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1997 Isuzu Trooper LTD 3.2 V6 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark companion flange on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove exhaust and transfer protectors.
- Remove bolts and then remove driveline from front final drive and transfer case.
- Reverse procedure to install noting the following:
- Torque driveline to transfer companion flange mounting bolts to 46 ...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Trooper DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Trooper AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Trooper cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1997 Isuzu Trooper S 3.2 V6 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with a...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Trooper DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
