Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1997 Mazda Miata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda Miata cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Replacement
Vehicle: 1997 Mazda Miata 1.8 L4 GAS
Replacement
- Remove master cylinder as outlined in "Hydraulic Brake Systems."
- Remove clutch pipe holder, if equipped, then disconnect vacuum hose from power brake unit.
- Disconnect pushrod fork from brake p...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda Miata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda Miata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda Miata cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> B-Series -> Except B-Series -> Master Cylinder Overhaul -> Wheel Cylinder Overhaul
Vehicle: 1997 Mazda Miata 1.8 L4 GAS
Master Cylinder Overhaul
Except B-Series
- Remove brake fluid from reservoir after removal of master cylinder.
- Refer to Figs. through , for master cylinder disassembly.
- Visually inspect all components and repair or replace any faulty components.
- Reverse procedure to assemble.
B-Series
- Clean outside of master cylinder and drain fluid after removal.
- Remove snap ring by depressing rear piston, Fig. .
- Remove primary piston from master cylinder, then remove secondary piston by directing compressed air ...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda Miata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda Miata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda Miata cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting
Vehicle: 1997 Mazda Miata 1.8 L4 GAS
Refer to Fig. , for assistanc...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda Miata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda Miata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda Miata cars and light trucks from 1990+.
Anti-lock Brakes -> Component Testing -> 1997 -> 1998-2001 -> 1999-2001 -> ABS Control Module -> ABS Control Unit -> ABS Hydraulic Unit -> ABS Motor -> ABS Motor & Harness -> ABS Motor & Harness To ABS Control Module -> ABS Relay -> ABS Warning Light -> B-Series -> Clearance Inspection -> Control Unit -> Fail-Safe Relay -> Hydraulic System -> Hydraulic Unit -> Miata -> Millenia & Protege -> Motor Relay -> MPV -> MX-6 & 626 -> Pressure Differential Switch -> Rear Axle Speed Sensor -> Rotor Inspection -> Solenoid Valve -> Solenoid Valve & Valve Relay -> Valve Relay -> Voltage Inspection -> Wheel Speed Sensor
Vehicle: 1997 Mazda Miata 1.8 L4 GAS
B-Series
ABS Control Module
1999-2001
Refer to Figs. through , for component testing procedures.
ABS Warning Light
If warning light is inoperative at all times, proceed as follows:
- Inspect warning light bulb; replace as required.
- Inspect No. 10 15A fuse; replace as required.
Hydraulic Unit
1997
Disconnect hydraulic unit connector and measure resistance between terminals 1 and 3 at unit. Resistance should be 18-26 K ohms. If not, replace hydraulic unit.
Rear Axle Speed Sensor
1997
- Raise and support vehicle.
- Remove differential cover and measure clearance between rear axle speed sensor and s...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda Miata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda Miata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda Miata cars and light trucks from 1990+.
Hydraulic Brake Systems -> Diagnosis & Testing -> Brake Fluid Level Sensor -> Proportioning Valve
Vehicle: 1997 Mazda Miata 1.8 L4 GAS
Proportioning Valve
- Connect pressure testing equipment as outlined in, Figs. through , then bleed air from brake system as outlined under " Brake System Bleed."
- Depress pedal until master cylinder pressure measures A, then record rear brake pressure (A').
- Depress pedal with additional force until master cylinder pressure measures A, then record rear brake pressure again (B').
- If pressures are...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda Miata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda Miata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda Miata cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1997 Mazda Miata 1.8 L4 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydraulic pres...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda Miata BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 Mazda Miata vehicle. |
Access the Complete guide! |