Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1997 Subaru Impreza car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1997 Subaru Impreza automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1997 Subaru Impreza
- 1997 Subaru Impreza L 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 1997 Subaru Impreza Outback 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 1997 Subaru Impreza Brighton 1.8 H4 GAS, CC:1781, Fuel Injection, Engine VIN:, Desg:2
- 1997 Subaru Impreza Brighton 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Impreza cars and light trucks from 1990+.
Anti-lock Brakes -> Impreza -> System Service -> ABS Control Module & Hydraulic Control Unit -> ABS Wheel Sensor -> Brake System Bleed -> Component Replacement -> Front -> G Sensor -> Rear
Vehicle: 1997 Subaru Impreza L 2.2 H4 GAS
Brake System Bleed
- Start with wheels connecting to secondary chamber of master cylinder.
- Inspect for leaks at joints and connection in brake system, repair as necessary.
- Fit one end of a suitable vinyl hose over brake bleeder and place other end into a container filled with brake fluid.
- Slowly depress brake pedal and keep depressed.
- Open bleeder crew and release fluid for one to two seconds.
- Close bleeder screw and release pedal.
- Repeat steps until all air is discharged from system.
Component Replacement
ABS Wheel Sensor
Front
- Disconnect ABS sensor connector located in engine compartment ne...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Impreza cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 1997 Subaru Impreza L 2.2 H4 GAS
Master Cylinder
- Remove master cylinder from vehicle.
- Remove cylinder pin, Fig. .
- Push piston inward, then remove snap ring.
- Apply pressure to piston assembly while Inserting a small screwdriver into window of piston retainer and raise piston retainer latch, Fig. .
- Remove primary and secondary piston assemblies. Do not disassemble pistons. if disassembled, the spring settings will change.
- Inspect master cylinder inside diameter to piston clearance, Service limit is not to exceed 0.043 inch.
- Clean all parts with clean brake fluid, do...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Impreza cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 1997 Subaru Impreza Brighton 1.8 H4 GAS
Master Cylinder
- Remove master cylinder from vehicle.
- Remove cylinder pin, Fig. .
- Push piston inward, then remove snap ring.
- Apply pressure to piston assembly while Inserting a small screwdriver into window of piston retainer and raise piston retainer latch, Fig. .
- Remove primary and secondary piston assemblies. Do not disassemble pistons. if disassembled, the spring settings will change.
- Inspect master cylinder inside diameter to piston clearance, Service limit is not to exceed 0.043 inch.
- Clean all parts with clean brake fluid, do...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Impreza cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Forester & Impreza -> Front -> Legacy & Outback -> Overhaul -> Rear -> Replacement -> SVX
Vehicle: 1997 Subaru Impreza Brighton 1.8 H4 GAS
Replacement
Front
- Raise and support vehicle.
- Remove front wheels.
- Disconnect brake hose from caliper. Plug hose to prevent fluid leakage.
- Remove caliper lockpin, rotate caliper on guide pin, then remove caliper, Figs. and .
- Reverse procedure to install noting the following:
- Refer to Figs. and for tightening values.
- After completing installation, bleed hydraulic system as outlined under, "Hydraulic Brake Systems," "Brake System Bleed."
Rear
- Raise and support vehicle.
- Remove rear wheels.
- Disconnect brake hose from caliper. Plug brake to prevent fluid leakage.
- Remove caliper retaining bo...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Impreza cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Brake Booster, Replace -> Forester, Impreza, Legacy & Outback -> Overhaul -> SVX
Vehicle: 1997 Subaru Impreza Brighton 1.8 H4 GAS
Brake Booster, Replace
Forester, Impreza, Legacy & Outback
- Disconnect brake fluid level indicator connector, if equipped.
- Remove master cylinder assembly.
- Disconnect vacuum hose from brake booster.
- Working from inside the passenger compartment, remove snap pin and operating rod clevis pin from brake pedal assembly.
- Remove brake booster retaining nuts, then brake booster from vehicle.
- Reverse procedure to install. Torque brake booster retaining nuts to 10-17 ft. lbs.
SVX
- Raise and support vehicle and remo...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Impreza BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Impreza AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Impreza cars and light trucks from 1990+.
Anti-lock Brakes -> Impreza -> Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Less Select Monitor -> Preliminary Inspection -> Wiring Diagram -> With Select monitor
Vehicle: 1997 Subaru Impreza Brighton 1.8 H4 GAS
Preliminary Inspection
- Ensure battery voltage is 12 volts or more and specific gravity is above 1.260.
- Inspect brake fluid level and for brake fluid leakage.
- Inspect brake drag.
- Inspect brake pads and rotors.
- Inspect tires for excessive wear and proper inflation.
Accessing Diagnostic Trouble Codes
Less Select Monitor
When on board diagnosis of the ABS control module detects a problem, the information (up to a maximum of three) will be stored in the EEPROM as a diagnostic trouble code (DTC). When there are more than three, the most recent three will be stored. Stored codes will stay ...
[[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Impreza BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
