Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1997 Suzuki Swift car and truck
repair procedures including Suzuki engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1997 Suzuki Swift automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1997 Suzuki Swift
- 1997 Suzuki Swift GA 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:2
- 1997 Suzuki Swift DLX 1.3 L4 GAS, CC:1298, CID:79, Fuel Injection, Aspiration:79, Engine VIN:, Desg:2
BRAKE SERVICE PROCEDURES FOR 1997 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting -> Brake Pull -> Brake Warning Light On Or Flashing, After Engine Start -> Brake Warning Light On, w/Brake Pedal Applied -> Dragging Brakes -> Excessive Pedal Travel -> Low Braking Force
Vehicle: 1997 Suzuki Swift GA 1.3 L4 GAS
Low Braking Force
- Fluid leakage from brake lines and/or hoses.
- Air in brake system.
- Malfunctioning wheel cylinder and/or caliper assembly.
Brake Pull
- Malfunctioning wheel cylinder and/or caliper assembly.
- Loose calipers.
- Restricted brake line or hose.
Excessive Pedal Travel
- Partial brake system failure.
- Insufficient fluid in master cylinder reservoirs.
- Air in system.
Dragging Brakes
- Master c...
CLICK HERE TO GET FULL ACCESS TO 1997 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 1997 Suzuki Swift GA 1.3 L4 GAS
Master Cylinder
- Clean any dirt from around reservoir cap. Remove cap, then drain brake fluid into appropriate container.
- Remove reservoir connector screw, Fig. , then the reservoir.
- Disconnect brake lines from master cylinder. Do not allow brake fluid to get on painted surfaces.
- Remove master cylinder attaching bolts, then the master cylinder.
- Adjust clearance of booster piston rod to master cylinder piston as follows:
- Push piston rod several times to ensure reaction disc is in place.
- Measure with gasket in place on master cylinder and booster at atmospheric pressure.
- Set measurin...
CLICK HERE TO GET FULL ACCESS TO 1997 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Suzuki Swift cars and light trucks from 1990+.
Anti-lock Brakes -> Description
Vehicle: 1997 Suzuki Swift DLX 1.3 L4 GAS
The ABS controls the fluid pressure applied to the wheel cylinder of each brake from the master cylinder so that each wheel is not locked even when hard braking...
CLICK HERE TO GET FULL ACCESS TO 1997 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Suzuki Swift cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Assemble -> Disassemble -> Installation -> Removal
Vehicle: 1997 Suzuki Swift DLX 1.3 L4 GAS
Removal
- Remove approximately 2/3 of brake fluid from master cylinder.
- Raise and support vehicle.
- Mark relationship between front wheel and axle, then remove wheel and tire assembly.
- Remove inlet fitting attaching bolt, copper washer and inlet fitting from caliper housing. Plug opening in inlet fitting to prevent fluid loss and contamination. Do not crimp brake hose, as this may damage internal structure of hose. If only shoe and lining assemblies are to be replaced, do not disconnect brake line fitting from caliper.
- Remove caliper slide pins and caliper.
- Remove shoe and lining assembl...
CLICK HERE TO GET FULL ACCESS TO 1997 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description
Vehicle: 1997 Suzuki Swift DLX 1.3 L4 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydraulic pressure ...
CLICK HERE TO GET FULL ACCESS TO 1997 Suzuki Swift BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Suzuki Swift AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Suzuki Swift cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Esteem & Swift -> Grand Vitara, Sidekick, Vitara & X-90 -> Master Cylinder -> System Bleed
Vehicle: 1997 Suzuki Swift DLX 1.3 L4 GAS
Brake fluid is extremely damaging to paint. If fluid should accidentally touch painted surface, immediately wipe fluid from paint and clean painted surface.
System Bleed
Esteem & Swift
The hydraulic lines of the brake system are based on a diagonal split system. When a brake line or hose is disconnected, bleeding operation must be performed at both ends of the line disconnected.
- Fill master cylinder reservoir. Reservoir should be kept at least half full during bleeding operation.
- Remove bleeder plug cap, then attach vinyl tube to bleeder plug of component to be bled. Insert other ...
CLICK HERE TO GET FULL ACCESS TO 1997 Suzuki Swift BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1997 Suzuki Swift vehicle.
|
| Access the Complete guide! |
