Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Audi Cabriolet car and truck
repair procedures including Audi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1998 Audi Cabriolet automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1998 Audi Cabriolet AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Audi Cabriolet cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> A4, A6, A8, S4 & S6 -> ABS Return Pump Does Not Run, Relay Good, Tester In Position 3 -> ABS Return Pump Does Not Run, Tester In Position 3 -> Accessing Diagnostic Trouble Codes (DTC) -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Electrical Testing -> Hydraulic Modulator High & Low Pressure Testing -> LED 1 & 3 Do Not Light, Tester In Position 1 -> LED 18 Does Not Light -> LED 19 Does Not Light -> LED 35 Does Not Light -> LED 4 Does Not Light, Tester In Position 1 -> LED 4, 2, 35, 18 & 19 Do Not Light, Tester In Position 1 -> LED For Alternator Does Not Go Out When Engine Starts -> LED For Alternator Does Not Light, Tester In Position 2 -> LED For Brakes Does Not Go Out When Brake Pedal Is Depressed -> LED For Brakes Does Not Light -> No Response From Selected Sensor, Tester In Position 6 -> Read Measuring Value Block -> S6 -> Sensor Signal On Meter Below Minimum Value -> TT -> With LED Type Tester -> With Scan Tool -> Wrong Solenoid Valve Operates, Tester In Position 5
Vehicle: 1998 Audi Cabriolet 2.8 V6 GAS
With LED Type Tester
LED 1 & 3 Do Not Light, Tester In Position 1
Refer to Fig. ,for LED identification numbers. Weaker illumination of an LED indicates a contact resistance in respective circuit.
- Inspect for continuity between ABS control unit connector terminal 34 and ground at battery ground cable (LED 1), Fig. .
- Inspect for continuity between ABS control unit connector terminal 10 and ground at battery ground cable (LED 3).
- If continuity does not exist, repair shorted or open circuit.
LED 4 Does Not Light, Tester In Position 1
Refer to Fig. ,for LED identification. Weaker illum...
[[table data]] [[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 1998 Audi Cabriolet BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Audi Cabriolet AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Audi Cabriolet cars and light trucks from 1990+.
Disc Brakes -> Single Piston Rear Disc Brakes -> Brake Pad Service -> Except TT -> TT
Vehicle: 1998 Audi Cabriolet 2.8 V6 GAS
Except TT
- Raise and support vehicle, then remove wheel assemblies.
- If brake pads are to be used again, mark installed positions for installation reference.
- Remove caliper housing to carrier mounting bolts, then the caliper housing, Fig. .
- Remove brake pads from carrier.
- Extract part of brake fluid from reservoir using a suitable bleeder bottle, then install piston using installation tool No. 3272, or equivalent.
- Install brake pads, then the caliper housing and tighten to specifications.
- Install wheel assemblies and lower vehicle.
- On A4 and A8 models, depress brake pedal firmly several...
CLICK HERE TO GET FULL ACCESS TO 1998 Audi Cabriolet BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Audi Cabriolet AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Audi Cabriolet cars and light trucks from 1990+.
Anti-lock Brakes -> System Coding -> TT
Vehicle: 1998 Audi Cabriolet 2.8 V6 GAS
TT
Refer to Fig. fo...
CLICK HERE TO GET FULL ACCESS TO 1998 Audi Cabriolet BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Audi Cabriolet AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Audi Cabriolet cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1998 Audi Cabriolet 2.8 V6 GAS
The following procedure has been modified by a Technical Service Bulletin.
To bleed brake system, use a catch bottle with a transparent hose attached so brake fluid can be inspected for air bubbles.
- Connect brake pressure bleeding tool No. VAG 1869, or equivalent, per tool manufacturer's instructions.
- Bleed brakes in following sequence:
- Righ...
CLICK HERE TO GET FULL ACCESS TO 1998 Audi Cabriolet BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Audi Cabriolet AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Audi Cabriolet cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> A4 & S4 -> A4, A6, S4 & S6 -> A6 & S6 -> A6, Cabriolet & S6 -> A8 -> Brake System Bleed -> Cabriolet -> Component Replacement -> Electronic Control Unit -> Front Wheel Speed Sensors -> Hydraulic Control Unit -> Hydraulic Control Unit Mounting Bracket -> Rear Wheel Speed Sensors -> TT
Vehicle: 1998 Audi Cabriolet 2.8 V6 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for procedures.
Component Replacement
Electronic Control Unit
A4, A6, S4 & S6
The electronic control unit is located beneath the lefthand side of the rear seat.
- Turn ignition Off.
- Remove rear seat.
- Remove spring retaining electrical connector, then disconnect electrical connector.
- Remove screws securing control unit.
- Reverse procedure to install.
A8
- Remove lower slot cover from between knee bolster and lower column cover.
- Remove knee bolster.
- Remove ABS control module.
- Disconnect ABS control module electrical harness connector.
- Reverse procedure...
CLICK HERE TO GET FULL ACCESS TO 1998 Audi Cabriolet BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Audi Cabriolet AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Audi Cabriolet cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> A4 & S4 -> A6, S6 & Cabriolet -> A8 -> Brake Pressure Regulator -> Master Cylinder -> TT
Vehicle: 1998 Audi Cabriolet 2.8 V6 GAS
Master Cylinder
A4 & S4
- Remove driver's side storage compartment.
- Separate brake pedal from master cylinder pushrod as follows:
- Remove stop lamp switch.
- Insert brake pedal release tool No. T10006, or equivalent, from below, Fig. .
- Hold brake pedal tightly.
- Lift catch off push rod using a slight pull on release tool " A."
- Keep tension on tool to prevent pushrod from engaging catches.
- Separate brake pedal from master cylinder pushrod " B."
- Connect bleeder hose and bleeder bottle to lefthand front brake caliper bleeder valve, then open bleeder valve.
- Operate brake pedal to pump out as much ...
CLICK HERE TO GET FULL ACCESS TO 1998 Audi Cabriolet BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1998 Audi Cabriolet vehicle.
|
| Access the Complete guide! |
