Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Honda CR-V car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1998 Honda CR-V automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1998 Honda CR-V
- 1998 Honda CR-V EX 2.0 L4 GAS, CC:1972, Fuel Injection
- 1998 Honda CR-V LX 2.0 L4 GAS, CC:1972, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 1998 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Honda CR-V cars and light trucks from 1990+.
Disc Brakes -> Tightening Specifications
Vehicle: 1998 Honda CR-V EX 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1998 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Honda CR-V cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder, Replace
Vehicle: 1998 Honda CR-V EX 2.0 L4 GAS
Master Cylinder, Replace
- Remove master cylinder reservoir cap, then suck fluid from reservoir with a suitable syringe.
- Disconnect brake lines from master cylinder, then all necessary electrical connectors.
- Remove master cylinder to brake booster retaining nuts.
- Remov...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Honda CR-V cars and light trucks from 1990+.
Drum Brakes -> Tightening Specifications
Vehicle: 1998 Honda CR-V LX 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1998 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Honda CR-V cars and light trucks from 1990+.
Power Brake Units -> Adjustments -> Pushrod Clearance -> Pushrod Length
Vehicle: 1998 Honda CR-V EX 2.0 L4 GAS
Pushrod Clearance
Master cylinder pushrod-to-piston clearance must be checked and adjusted before installing master cylinder.
- Using pushrod adjustment gauge tool No. 07JAG-SD40100, or equivalent, adjust bolt so top of it is flush with end of master cylinder piston, Fig. .
- Install master cylinder rod seal between pushrod bolt adjustment gauge and brake booster.
- Without disturbing position of adjusting bolts, install gauge upside down on booster and torque nuts to 11 ft. lbs.
- Connect booster in line with a vacuum gauge, and maintain an engine speed that will deliver 20 inches of vacuum. Th...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Honda CR-V cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> Accord, Odyssey & Prelude -> Civic, CR-V, del Sol & S2000 -> Power Booster Overhaul -> Power Booster, Replace
Vehicle: 1998 Honda CR-V EX 2.0 L4 GAS
Power Booster, Replace
Accord, Odyssey & Prelude
- Remove master cylinder as outlined under "Hydraulic Brake Systems."
- Disconnect vacuum hose from booster, then remove vacuum hose bracket.
- Remove throttle control cable bracket, then disconnect engine wire harness connectors.
- On models equipped with manual transmission, remove clutch reservoir and reservoir bracket. Do not disconnect clutch hose from reservoir.
- On all models, loosen pushrod locknut, then remove cotter pin and joint pin.
- Remove clevis from operating rod of brake booster, then four booster mounting nuts.
- Pull brake bo...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Honda CR-V cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> 1997-2001 -> 1997-98 -> 1999-2001 -> 2002 -> Accord -> Civic -> CR-V -> Del Sol -> Major Adjustment -> Minor Adjustment -> Odyssey -> Parking Brake -> Prelude -> S2000
Vehicle: 1998 Honda CR-V LX 2.0 L4 GAS
Parking Brake
Accord
- Raise and support vehicle.
- On models equipped with rear disc brakes, ensure parking brake arm on rear caliper is in contact with brake caliper pin.
- On all models, pull parking brake lever up one click, then remove rear center console lid.
- Tighten adjusting nut until brakes drag slightly when turning rear wheels.
- Fully release parking brake, ensure brakes do not drag when turning rear wheels.
- Fully apply parking brake, ensure wheels do not turn.
- Install console lid.
Civic
- Raise and support vehicle.
- On models equipped with rear disc brakes, ensure parking brake arm on rear c...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda CR-V BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
