1998 Honda Passport Driveline, U-Joint & CV Axles Replacement (ONLINE REPAIR MANUALS)

Auto Parts Search


Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!
Help me findSearch
Get Full Access Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Honda Passport car and truck repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your 1998 Honda Passport automobile. Try the Automotix DIY solution today!
DIY REPAIR SAMPLES > CONTINUE EXPLORING >

We have info for following modifications of 1998 Honda Passport

  • 1998 Honda Passport EX 3.2 V6 GAS, CC:3165, Fuel Injection
  • 1998 Honda Passport LX 3.2 V6 GAS, CC:3165, Fuel Injection

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Passport AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Honda Passport cars and light trucks from 1990+.

CV AXLE SHAFT, Replace
Vehicle: 1998 Honda Passport LX 3.2 V6 GAS

Replacement procedures for left and right driveshafts are the same.

  • Raise and support front of vehicle, then remove front wheels.
  • Drain transaxle.
  • Raise locking tab on spindle nut, then remove nut.
  • Remove self-locking nut and self-locking bolt. Replace self-locking bolt if you can easily thread a non-self-locking nut past their nylon locking inserts.
  • Remove damper fork, then cotter pin from lower arm ball joint castle nut and remove nut.
  • Install hex nut on ball joint. Ensure nut is flush with ball joint pin end, or threaded section of ball joint pin might be damaged by ball joi...

CLICK HERE TO GET FULL ACCESS TO 1998 Honda Passport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Passport AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Honda Passport cars and light trucks from 1990+.

DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1998 Honda Passport EX 3.2 V6 GAS

Disassemble

Snap Ring Type

This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.

  • Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
  • Tap outside of bearing cap with a drift to loosen snap ring.
  • ...

CLICK HERE TO GET FULL ACCESS TO 1998 Honda Passport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Passport AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Honda Passport cars and light trucks from 1990+.

CV AXLE SHAFT, Replace
Vehicle: 1998 Honda Passport EX 3.2 V6 GAS

Replacement procedures for left and right driveshafts are the same.

  • Raise and support front of vehicle, then remove front wheels.
  • Drain transaxle.
  • Raise locking tab on spindle nut, then remove nut.
  • Remove self-locking nut and self-locking bolt. Replace self-locking bolt if you can easily thread a non-self-locking nut past their nylon locking inserts.
  • Remove damper fork, then cotter pin from lower arm ball joint castle nut and remove nut.
  • Install hex nut on ball joint. Ensure nut is flush with ball joint pin end, or threaded section of ball joint pin might be damaged by ball joi...

CLICK HERE TO GET FULL ACCESS TO 1998 Honda Passport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Passport AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Honda Passport cars and light trucks from 1990+.

DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1998 Honda Passport LX 3.2 V6 GAS

Disassemble

Snap Ring Type

This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.

  • Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
  • Tap outside of bearing cap with a drift to loosen snap ring.
  • ...

CLICK HERE TO GET FULL ACCESS TO 1998 Honda Passport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Passport AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Honda Passport cars and light trucks from 1990+.

DRIVESHAFT, Replace
Vehicle: 1998 Honda Passport EX 3.2 V6 GAS

  • Place vehicle in neutral.
  • Release parking brake.
  • Raise and support vehicle and support it with safety stands in proper locations.
  • Detach outer retainer of center support bearing and remove center support bearing with suitable tool.
  • Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
  • Remove bolts, nuts, and washers from ...

CLICK HERE TO GET FULL ACCESS TO 1998 Honda Passport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Passport AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Honda Passport cars and light trucks from 1990+.

DRIVESHAFT, Replace
Vehicle: 1998 Honda Passport LX 3.2 V6 GAS

  • Place vehicle in neutral.
  • Release parking brake.
  • Raise and support vehicle and support it with safety stands in proper locations.
  • Detach outer retainer of center support bearing and remove center support bearing with suitable tool.
  • Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
  • Remove bolts, nuts, and washers from ...

CLICK HERE TO GET FULL ACCESS TO 1998 Honda Passport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

Shop online for auto body parts, engines, wheels, lights...

More parts
Help me findSearch
Auto Repair Quick Search
Help me find
Search DIY repair manuals by VIN...
Vehicle Identification Number is a unique serial number used by the automotive industry to identify individual motor vehicles

Find out what info we have for your vehicle

Get the Complete Technical Service Bulletins!
Get the Complete Technical Service Bulletins!Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Honda Passport vehicle.
Access the Complete guide!
Need To Fix Your Car or Truck?
Save Money With Free Car Insurance Quote
FREE car insurance quote
Enter Zip Code:
Auto Repair Quick Search
Help me find