Auto Parts Search
We have info for following modifications of 1998 Toyota 4runner
- 1998 Toyota 4runner 2.7 L4 GAS, CC:2694, Fuel Injection, Engine VIN:, Desg:M
- 1998 Toyota 4runner 3.4 V6 GAS, CC:3378, Fuel Injection, Engine VIN:, Desg:N
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota 4runner AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota 4runner cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1998 Toyota 4runner 2.7 L4 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
- Tap outside of bearing cap with a drift to loosen snap ring.
- ...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota 4runner DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota 4runner AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota 4runner cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1998 Toyota 4runner 2.7 L4 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolt...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota 4runner DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota 4runner AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota 4runner cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1998 Toyota 4runner 3.4 V6 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
- Tap outside of bearing cap with a drift to loosen snap ring.
- ...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota 4runner DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Toyota 4runner AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1998 Toyota 4runner cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1998 Toyota 4runner 3.4 V6 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolt...
CLICK HERE TO GET FULL ACCESS TO 1998 Toyota 4runner DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Toyota 4runner vehicle. |
Access the Complete guide! |